RV 21260/21263 - Launch Pad Seat and Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 21000 - Revolution Post Top Cap The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified. RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1968 - Warp Rung Wall RV The Warp Rung Wall RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Warp Rung Wall 1 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, and 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Warp Rung Mall 2 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and stainless steel housings and will be Powder Coated as specified. RV-1925-PT - Hex Net Tower Middle RV The Hex Net Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Platform Plug Top and Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Hex Net Tower Net RV shall be made from 16 mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. The Hex Net Platform Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Post Anchor Bracket RV shall be fabricated using a 1/4" thick stainless steel mounting bracket with welded 3/16" thick stainless steel anchor and will be Powder Coated as specified. RV-1925-BS - Hex Net Tower Bottom RV The Hex Net Bottom Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Platform Plug Top and Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Hex Net Tower Net RV shall be made from 16-mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. The Post Anchor Bracket RV shall be fabricated using a 1/4" thick stainless steel mounting bracket with welded 3/16" thick stainless steel anchor and will be Powder Coated as specified. RV-1925 - Hex Net Tower Top RV The Hex Net Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Platform Plug Top and Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Hex Net Tower Top Net RV shall be made from 16 mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. The Net Tower Top Rail RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick stainless steel anchors and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Hex Net Platform Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Post Anchor Bracket RV shall be fabricated using a 1/4" thick stainless steel mounting bracket with welded 3/16" thick stainless steel anchor and will be Powder Coated as specified. RV 1293 - Net Tower Ladder RV The Post Anchor Bracket RV shall be fabricated using a 1/4" thick stainless steel mounting bracket with welded 3/16" thick stainless steel anchor and will be Powder Coated as specified. The Net Tower Ladder RV shall be made from 16 mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. RV 1286 - Arched Lunar Climber RV The Arched Wall Climber Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arched Panel Climber Frame RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.660" O.D. 11 gauge steel support rails with welded 1/4" thick steel tabs mounting brackets. The Arched Panel Climber Frame RV will be Powder Coated as specified. RH-21004 - Single Arm Event Hanger Hybrid The Event Hanger RH shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel clevis and stainless steel pin and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-18030 - Orbital Shade The Orbital Shade - Post Connectors shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel brackets and tabs and shall have a powder coat finish. The Orbital Shade - Curved Extensions shall be fabricated using 5" O.D. 11 gauge steel tubing with a welded 1/4" thick steel cap and 3/8" thick steel brackets and shall have a powder coat finish. The Orbital Shade - Outside Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and a welded nut and shall have a powder coat finish. The Orbital Shade - Canopy Support Frames shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel tabs and shall have a powder coat finish. The Orbital Shade Canopy shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel tensioner. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 1385 - Dual Dino Rider The Dual Dino Rider Body, Seat, Handles, Footrests and Spacers shall be made from high-density 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV-stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Spring Mount Puck shall be precision die-cast from high-strength aluminum alloy and will be Powder Coated as specified. The Bottom Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Top Spring Mount Plate shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. The Spring Rider Bracket shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1288 - Dual Arch Rope Net Cross Loop Climber The Arch Rope Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end clevises. The Arch Rope Net Climber Side Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/16" thick steel anchors and 3/8" thick steel mounting tab and shall have a powder coat finish. The Dual Rope Net Cross Loop Climber Frame RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 3/16" thick steel anchors, 3/8" thick steel mounting tabs, 1/4" thick stainless steel mounting bracket, and 5/8" round bar steel and shall have a powder coat finish. The Dual Rope Net Cross Loop Climber Frame Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 3/16" thick steel anchors, 1/4" thick steel mounting tabs, stainless steel housing, and 5/8" round bar steel and shall have a powder coat finish. The Dual Rope Net Cross Loop Climber Frame R5 shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 3/16" thick steel anchors, 1/4" thick steel mounting clevises, 3/8" thick steel tabs, and 5/8" round bar steel and shall have a powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. 1219 - Deep Rung Arch Climber The Arch Climber Deep Rung shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.