R5-1660-1669 - Panel Pal Roto R5 SMALL BELL: Shall be die-cast using 356.1 aluminum alloy and will have a multi-stage baked-on powder coat finish. HDPE PARTS (ALL): Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PANEL PAL ROTO FRAME: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PANEL PAL MIRROR STEEL: Shall be fabricated using 16 ga. 304 #8 HPSS. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1632 - Bugeye Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bugeye Bubble shall be fabricated from 3/16" Clear Polycarbonate. 1602-BBL - Bubble Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bubble Window shall be fabricated from 3/16" Clear Polycarbonate. R5-1535-XTD - X2 Crawl-Netix Transition The Support Plates shall be fabricated from 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The X2 Tower SS Plate (Panel 2) & X2 Tower Tube Extension 17 Degree shall be fabricated from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Crawl Tube Elbows shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The X2 SSS HDPE Trim & R3.5 Tube Panel Stiffener shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Rail Section shall be fabricated from 1.660" O.D. 11 gauge steel tubing, 1.029" O.D. 14 gauge steel tubing, 10 gauge sheet steel, and 3/16" steel clevises and will have a multi-stage baked-on powder coat finish. The Crawl-Netix Net Section shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. 13601-X2 - X2 View Panels The Main Panels shall be fabricated using punched 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Panel Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1349-X2 - X2 TOWER SLIDE SIT DOWN ENTRY The X2 Tower Slide Entry shall be punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff (TM) coated after fabrication. The Slide Tube Extension shall be punched, formed and welded 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Slide Panels shall be punched and formed from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Trim & Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1709-X2 - PORTAL SLIDE SPIRAL X2 - 1316-RE - Twister Slide Roto Entry The Twister Slide-Hood Standard shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga. steel tubing and will have a multi-stage baked-on powder coat finish. The Twister Slide Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 18031 - Corrugated Hex Roof The Braces, Roof Sections & Ridge Caps shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Steel Hex Roof Cap shall be fabricated using punched, formed and welded 14 gauge sheet steel and will be Powder Coated as specified. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Roof Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5-18030 - Orbital Shade The Orbital Shade - Post Connectors shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel brackets and tabs and shall have a powder coat finish. The Orbital Shade - Curved Extensions shall be fabricated using 5" O.D. 11 gauge steel tubing with a welded 1/4" thick steel cap and 3/8" thick steel brackets and shall have a powder coat finish. The Orbital Shade - Outside Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and a welded nut and shall have a powder coat finish. The Orbital Shade - Canopy Support Frames shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel tabs and shall have a powder coat finish. The Orbital Shade Canopy shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel tensioner. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5 1126 - Center Access Hex Deck The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck Barrier and Handle shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1945 - Orbit Wheel The Orbit Wheel Frame shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge supports, 1/4" stainless steel mounting brackets and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Orbit Wheel Frame R35 and R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 11 gauge supports, 1/4" steel split collars and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Traverse Wheel shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded machined stainless steel hub and will have a multi-stage baked-on powder coat finish. The Wheel Traverse Cap shall be fabricated using precision cut 10 gauge stainless steel. The Split Collar Half hall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1414 - Lily Pad Step-Up The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Lily Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Lily Pad Step-Up Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1220 - Centipede Climber The Centipede Climber shall have a center support constructed of 2.375" O.D. 10 gauge Tube Steel with 1.315" O.D. 12 gauge Tube Steel stepping/gripping loops welded on and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.