5504 - Hill Hopper Link w/ Bailey Hill & Crane Ridge LOOP CLIMBER 270º PLATE: Shall be fabricated using 3/16" sheet steel A36 and will have a multi-stage baked-on powder coat finish. BAY BRIDGE w/ MOUNDS SUPPORT LEG STIFFNER: Shall be fabricated from 2.375" O.D. 11ga steel tubing with welded 3/8" sheet steel A36 tabs, 1/4" sheet steel A36 S Plate 2, a 3/16" sheet steel A36 pipe plug, and 3/16" AISI 304 stainless steel clevises and and will have a multi-stage baked-on powder coat finish. BAY BRIDGE w/ MOUNDS SIDE RAIL: Shall be fabricated from 2.375" O.D. 11ga steel tubing with AISI 303 stainless steel Slide Mount House, welded 3/8" sheet steel A36 tabs, and 3/16" sheet steel A36 clevises and will have a multi-stage baked-on powder coat finish. BAY BRIDGE w/ MOUNDS SLIDE SIDE RAIL: Shall be fabricated from 2.375" O.D. 11ga steel tubing with AISI 303 stainless steel Slide Mount Housing, welded 3/8" sheet steel A36 tabs, and 3/16" sheet steel A36 clevises and will have a multi-stage baked-on powder coat finish. BAY BRIDGE w/ MOUNDS SUPPORT LEGS LEFT & RIGHT: Shall be fabricated from 1-1/2" x 3" x .120 rectangular tube steel with 3/8" sheet steel A36, 1/4" sheet steel A36,12ga sheet steel A36 and 3/16" AISI 304 stainless steel and will have a multi-stage baked-on powder coat finish. TRI-RING: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". CHAIN: Shall be fabricated from 5/0 galvanized steel chain with silver shield finish. NETS: Shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. BAY BRIDGE SLIDE BELT & NFUSE BAY BRIDGE - BELT: Shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. HEX NET HUB RUBBER PLUG TOP AND BOTTOM: Shall be machined from high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. RUBBER FERRULE NUT: Shall be machined from high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. SOCKET CLAMP ROPE CLEVIS: Shall be fabricated using 3/16" AISI 304 stainless steel. TRANSFER BELT HANGER: Shall be fabricated using punched, formed and welded 12ga sheet steel A36 and shall be Play-Tuff™ coated after fabrication. BAY BRIDGE SUPPORT LEG HANDLE LEFT & RIGHT: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. NFUSE CURVED SWEDGED R35 SHADE POST: Shall be fabricated from 2.375" O.D. 11ga steel tubing and will have a multi-stage baked-on powder coat finish. BAY BRIDGE LADDER: Shall be fabricated from 2.375" O.D. 11ga and 1.315" O.D. 12ga steel tubing with welded 3/16" stainless steel clevises and machined ferrules and will have a multi-stage baked-on powder coat finish. NFUSE BAY BRIDGE OUTSIDE RAIL - NO BAY: Shall be fabricated from 2.375" O.D. 10ga steel tubing with welded 3/16" stainless steel clevises and 1/4" sheet steel clevises and will have a multi-stage baked-on powder coat finish. BAY BRIDGE TOP RAIL: Shall be fabricated from 3.5" O.D. 11ga steel tubing with 3/16" stainless steel clevises and will have a multi-stage baked-on powder coat finish. NFUSE BAY BRIDGE - TRI-RING CLIMBER RAIL: Shall be fabricated from 2.375" O.D. 10ga steel tubing with 1/4" and 3/16" stainless steel A36 clevises and will have a multi-stage baked-on powder coat finish. BAY BRIDGE SLIDE ARCH: Shall be fabricated from 3.5" O.D. 11ga steel tubing with 3/16" stainless steel clevises and will have a multi-stage baked-on powder coat finish. BAY BRIDGE SIDE RAILS: Shall be fabricated from 2.375" O.D. 11ga steel tubing with 3/16" AISI 303 stainless steel Slide Mount Pin, welded 3/16" aisi 304 stainless steel clevises and 1/4" sheet steel clevises and will have a multi-stage baked-on powder coat finish. NFUSE BAY BRIDGE OUTSIDE LOWER RAIL: Shall be fabricated from 2.375" O.D. 10ga steel tubing with welded 1/4" sheet steel A36 clevises and will have a multi-stage baked-on powder coat finish. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. MOUNTING INSERTS: Shall be precision die-cast from a high-strength aluminum alloy. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 3720 - Baily Hill The Mound shall be made using variable density EPS and artificial turf overlay. The 72” R3.5 Post – 4 Rivet shall be fabricated using 3.5" OD galv. T.S. 11ga. and will have a multi-stage baked on powder coat finish. The Post Caps shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Hardware shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 3740 - CRANE RIDGE The Mound shall be made using variable density EPDM with 3/8' nutserts, flex sphere mounting plates and artificial turf overlay. The Flex Sphere shall be made from GEZOFlex 0.5-1.5 EPDM rubber. The Flex Sphere Mount Plate shall be fabricated using punched and welded 1/4" HR Sheet steel, 12 gauge sheet steel, Ø1.990 and Ø1.029 tube steel and will have a multi-stage baked-on powder coat finish. The 72” R3.5 Post – 4 Rivet shall be fabricated using 3.5" OD galv. T.S. 11ga. and will have a multi-stage baked on powder coat finish. The Climber Rope shall be made from 24mm steel-reinforced woven rope with machined aluminum sleeves and end ferrules. The Post Caps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Hardware shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1316-RE - Twister Slide Roto Entry The Twister Slide-Hood Standard shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga. steel tubing and will have a multi-stage baked-on powder coat finish. The Twister Slide Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-12891-HEX - Center Access Climber-Hex The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck - Barrier shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 10 gauge HR sheet steel and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck - Handle and Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing, 3/8" HR sheet steel, 10 gauge HR sheet steel, 3/8" Tabs, and 3/16" Caps and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck - Ladder Leg shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck Ladder Deck Mount and Ladder Leg Surface Mount shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. R5 13011 - Half Square Deck Steel Wall R5 The Half Square Deck Steel Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with a welded 1/4" thick steel tab and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1428 - Burma Loop Traverse The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1214 - Climbing Wall The Chain Mount Bracket shall be laser-cut 1/4" thick steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Climb Chain Hanger shall be laser-cut 3/8" thick plate steel. The Climb Chain Hanger shall have clear zinc plating. The Grip Climb Wall shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Grip Climb Wall Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish and shall be Play-Tuff(TM) coated. The Grip Climb Wall Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 1.315" O.D. 12 gauge steel cross member with welded 3/8" thick steel tab and will be Powder Coated as specified. The Grip Ramp Bracket shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. The Ramp Grips shall be precision die-cast from a high strength aluminum alloy and shall have a thermoplastic coating. PC-2476 - Spin Max Tower The Spin Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Tower Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel top plate, 1/4" thick steel bottom plate and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Rope Clevis shall be formed using 3/16" thick stainless steel and will be Powder Coated as specified. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 1386 - Bear Single Spring Rider The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high-strength aluminum. The Spring Rider Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 1384 - Fish Single Spring Rider The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high-strength aluminum. The Spring Rider Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 1974 - Gyro-Pod Spinner The Gyro-Pod Capsule Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" x 1-1/2" flat steel reinforcement plates and stainless steel ball bearing and will be Powder Coated as specified. The Gyro-Capsule Top Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.900" O.D. 11 gauge steel supports, 1/4" thick stainless steel mounting brackets and stainless steel ball bearing and will be Powder Coated as finished. The Gyro-Pod Bearing Hub shall be fabricated using 2-1/4" O.D. machined steel hub with welded 1/4" thick steel plate and will be Powder Coated as specified. The Gyro-Pod Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Gyro-Pod Tread Plate shall be made from punched 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Gyro-Pod Ring Plate shall be made from precision cut 1/4" thick sheet steel and will be Powder Coated as specified. The Gyro-Pod End & Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Gyro-Pod Ring Spacer shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Ball Joint Socket Half shall be made from Ultra High Molecular Weight Polyethylene for lasting durability and minimal rotational resistance. The Split Collar Half shall be made from precision cut and formed 1/4" thick stainless steel and will be Powder Coated as specified. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1283 - Matrix Rope Net Wall The Matrix Rope Net Beam RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting brackets, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Matrix Rope Net Beam RH5 & RH3.5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting brackets and split collars, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as pecified. The Matrix Rope Net Beam R5 & R3.5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel split collars, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Matrix Rope Net shall be made from 16mm teel-reinforced rope with high-strength copolymer plastic intersection onnectors and machined aluminum end ferrules. The Post Anchor Bracket RV shall be fabricated using a 1/4" thick steel mounting bracket with welded 3/16" thick steel anchor and will be Powder Coated as specified. The Post Anchor Bracket R5 & R3.5 shall be fabricated using a 1/4" thick steel split collar with welded 3/16" thick steel anchor and will be Powder Coated as specified. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.