R5-1440 - SWAY-STEP GRIP TRAVERSE R5 SWAY-STEP GRIP TRAVERSE STATION: Shall be fabricated using 1.660 O.D. 11ga steel tubing with 5/8" HR round bar, 1/4" sheet steel disc plate plug AISI 304 stainless steel anchor clevises and will have a multi-stage baked on powder coat finish. SWAY-STEP GRIP ROPE: Shall be made from 16mm steel-reinforced rope with machined aluminum end ferrules. TRI-PAD CAP: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. TRI-PAD JUNGLE LINK 90 TOP FRAME R5: Shall be fabricated using 2.375 O.D. 10ga steel tubing with Ø2.375 AISI 303 round bar, 1/4" sheet steel tubing clevises and 3/16" stainless steel anchor clevises and will have a multi-stage baked on powder coat finish. TRI-PAD w/ HOLE: Shall be constructed of UV-stabilized rotationally molded, linear, low density polyethylene with anaverage wall thickness of .250". MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion 5207 - NFuse Inclined Belt Bay PEDESTAL TRANSFER DECK: Shall be fabricated using punched, formed and welded 12 gauge sheet steel with 1/2-13 stainless steel threaded rod and shall be Play-Tuff™ coated after fabrication. TRANSFER BELT HANGER: Shall be fabricated using punched, formed and welded 12 gauge A36 sheet steel and shall be Play-Tuff™ coated after fabrication. NFUSE INCLINED BELT BAY-COVER WELDMENT: Shall be fabricated using 1.660 OD 11 gauge tube steel with 1/4" A36 sheet steel and will have a multi-stage baked on powder coat finish. NFUSE INCLINED BELT BAY-TOP OUTSIDE RAIL: Shall be fabricated using 2.375" OD 11 gauge tube steel with 3/8"and 1/4" A36 sheet steel with 3/16" AISI 304 stainless steel and will have a multi-stage baked on powder coat finish. NFUSE INCLINED BELT BAY-SUPPORT RAIL: Shall be fabricated using 1.660 OD 11 gauge tube steel with 1/4" A36 sheet steel and will have a multi-stage baked on powder coat finish. NFUSE INCLINED BELT BAY-LEG: Shall be fabricated using 2.375" OD 11 gauge tube steel with 3/8", 1/4" and 3/16" A36 sheet steel and will have a multi-stage baked on powder coat finish. PEDESTAL TRANSFER DECK LEG: Shall be fabricated using 5" OD 7 gauge tube steel with 3/8" A36 sheet steel and will have a multi-stage baked on powder coat finish. LOOP CLIMBER 270º PLATE: Shall be fabricated using 3/16" A36 sheet steel and will have a multi-stage baked-on powder coat finish. TRANSFER BELT & NFUSE INCLINED BELT BAY BELT: Shall be made from 5/16' thick 3 ply reinforced rubber sheet. NFUSE INCLINED BELT BAY- PLATFORM WALL: Shall be fabricated using 2.375" OD 11 gauge, 1.660 OD 11 gauge, 1.315" OD 12 gauge tube steel and 1.5"x3"x.120" rectangle tube steel with 3/8" A36 sheet steel and 5/8" A36 round bar and will have a multi-stage baked on powder coat finish. NFUSE INCLINED BELT BAY- BOTTOM NET: Shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum ferrules. NFUSE INCLINED BELT BAY- NET RAIL: Shall be fabricated using 1.5"x3"x.120" rectangle tube steel with 1/4" A36 sheet steel and AISI 304 stainless steel anchor clevis and will have a multi-stage baked on powder coat finish. NFUSE MOLECULE BAY NETS: Shall be made from 16mm steel-reinforced rope with Rotomolded Turn Blocks, 3/4" HDPE spacers, machined aluminum ferrules and stainless steel hardware. CHAIN: Shall be 5/0 galvanized steel. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. MOUNTING INSERTS: Shall be precision die-cast from a high-strength aluminum alloy. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 12091 - Inclined Belt Climber PEDESTAL TRANSFER DECK: Shall be fabricated using punched, formed and welded 12 gauge A36 sheet steel with 1/2-13 threaded steel rod and shall be Play-Tuff™ coated after fabrication. TRANSFER BELT HANGER: Shall be fabricated using punched, formed and welded 12 gauge A36 sheet steel and shall be Play- Tuff™ coated after fabrication. LOOP CLIMBER 270º PLATE: Shall be fabricated using 3/16" A36 sheet steel and will have a multi-stage baked-on powder coat finish. BELT CLIMBER RAIL 48" LEFT & RIGHT: Shall be fabricated using 1.660 OD 11 gauge tube steel with 1/4" A36 sheet steel and 5/8" round bar and will have a multi-stage baked on powder coat finish. PEDESTAL TRANSFER DECK LEG: Shall be fabricated using 5" OD 7 gauge tube steel with 3/8" A36 sheet steel and will have a multi-stage baked on powder coat finish. BELT: Shall be made from 5/16' thick 3 ply reinforced rubber sheet. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 5701 - NFuse Single Slide Frame ARCH SLIDE LANDING: Shall be fabricated using punched, formed and welded 12 guage sheet steel and shall be Play- Tuff™ coated after fabrication. SINGLE SLIDE SPACER CANADA: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. SINGLE SLIDE LEG. Shall be fabricated using 1.660 OD 11ga tube steel, with 10ga sheet steel and will have a multi- stage baked on powder coat finish. NFUSE SINGLE SLIDE SHORT AND TALL WALLS (LEFT & RIGHT). Shall be fabricated using 1.315 and 1.029 OD tube steel, with 3/8", 1/4" and 12ga sheet steel and will have a multi-stage baked on powder coat finish. NFUSE SINGLE SLIDE - TOP RAIL. Shall be fabricated using 1.315 OD tube steel, with 3/8" and 3/16" sheet steel and will have a multi-stage baked on powder coat finish. POLY SLIDE 48" CANADA: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 5105 - NFUSE Platform Frame NFUSE FRAME: Shall be fabricated using 1-1/2" x 3" Rectangle Tube, 1.315" OD and 1.029" OD tube steel, 12ga sheet steel, and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1445-SEAT - UltraZip - Standard Seat PIPE PLUG: Shall be precision cut from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish. ULTRAZIP SEAT: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". ULTRAZIP SEAT ROPE: Shall be made from 24mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. ULTRAZIP SEAT FERRULE: Shall be machined from 6061-T6 aluminium. CHAIN: Shall be 316L 3/8" stainless steel. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. PC-1906 - Thunder Wedge The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Wedge Step shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Thunder Wedge Net Frame, Thunder Wedge Window & Insert Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick sheet steel and ASAI 304 stainless steel anchors and will have a multi-stage baked-on powder coat finish. The Thunder Wedge Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Thunder Wedge Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing, 3/16" sheet steel and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Cargo Net Surface Mount Bracket shall be fabricated using 1/4" sheet steel plate with a 3/16" stainless steel clevis and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. 1710-SUP - Twister Slide Support Assembly The Sectional Slide Support Bracket #2 shall be fabricated using 3/16"HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support shall be fabricated using Ø1.660 steel tubing, 3/16" HR sheet steel and 5/8"round bar and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Top shall be fabricated using Ø2.000 steel tubing and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Bottom shall be fabricated using Ø1.660 steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1980 - Counter Connection Assembly The Counter Connection Top shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Counter Connection Frame shall be fabricated using 1.5" x 3" rectangle tube with welded 12 gauge steel end caps and will have a multi-stage baked-on powder coat finish. The Counter Connection Leg shall be fabricated using 2.375" O.D. 11 gauge round tube, 1/4" HR sheet steel and 5/8" O.D. round bar and will have a multi-stage baked-on powder coat finish. The Counter Connection Post Mount shall be fabricated using 2.375" O.D. 11 gauge round tube and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1981 - Sensory Wall The Sensory Wall Leg shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 5/8" O.D. steel anchor and will have a multi-stage baked-on powder coat finish. The Sensory Wall Leg - Surface Mount shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Sensory Ramp Inserts shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Sensory Wall shall be fabricated using 1.029" O.D. 14 gauge and 1.315" O.D. 12 gauge steel tubing with welded 12 gauge and 1/4" thick steel tabs and flanges and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-RMKR - Small Rain Maker Panel The Small Rain Maker Back Panel, Rain Maker Cover, Rain Maker Rotator, Spinner Hub, and Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Rain Maker Window shall be made from .118 Polycarbonate sheet. 1414-C - Clover Seat The Spinner Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Clover Seat Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will have a multi-staged baked-on powder coat finish. The Clover Seat Leg Surface Mount shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 1/4" and 3/16" thick steel mounting plates with 10 gauge sheet steel gussets and will have a multi-staged baked-on powder coat finish. 5303 - NFuse Snake Net Extension The NFuse Snake Net Extension - Frame Rail Ground Mount and Surface Mount shall be fabricated using 1-1/2" x 3" rectangle tube, Ø1.315" OD tube steel, 1/4" HR sheet steel and AISI 304 Anchor Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" stainless steel. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1297 - Craze Wave Climb Wall The Craze Wave Climb Wall Arm shall be fabricated from 2.375" O.D. 11 gauge steel tubing with AISI 304 stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Craze Wave Climb Wall Arms Top and Bottom shall be fabricated from 2.375" O.D. 11 gauge steel tubing, 1/4" HR sheet steel clevises, and AISI 304 stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Craze Wave Climb Wall Leg Ground Mount shall be fabricated from 2.375" O.D. 11 gauge steel tubing with 3/8" HR round bar anchor and will have a multi-stage baked-on powder coat finish. The Craze Wave Climb Wall Leg Surface Mount shall be fabricated from 2.375" O.D. 11 gauge steel tubing with 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Craze Component shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Craze Wave Climb Wall Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" thick stainless steel. 1644-RND - Gear Panel Round The Gear Panel Components shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Gear Panel Windows shall be made from .118 Polycarbonate sheet plastic. 1690-BELL - Small Bell & Hammer Panel The Small Bell and Hammer Panel & Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bell shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-CHM - Small Chime Panel The Chime Panels & Chime Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Chime Panel Hubs & Spacers shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Chimes shall be fabricated using 0.75" Galvanized EMT 18ga and will have a multi-stage baked-on powder coat finish. The Chime Panel Bracket shall be punched and formed using 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. 1634 - Labyrinth Panel The Pin Ball Panel Mounting Ring, Labyrinth Panel Rotator, & Labyrinth Panel Front & Back Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Labyrinth Window shall be made from .118 thick polycarbonate sheet plastic. 1630 - Hour Glass Panel The Pin Ball Panel Mounting Ring, Hour Glass Rotator, & Pin Ball Clamping Rings shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Hourglass Window shall be made from .118 thick polycarbonate sheet plastic. 1445 - UltraZip The UltraZip End Beam shall be extruded from a high strength aluminum alloy with a welded machined aluminum pin. The UltraZip Straight Beam shall be extruded from a high strength aluminum alloy. The UltraZip Coupler shall be precision cut and welded 1/2" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel tie plate and will have a multi-stage baked-on powder coat finish. The UltraZip Junction Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel plate and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap shall be fabricated from 3/8" steel and will have multi-stage baked-on powder coat finish. The UltraZip Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel. The UltraZip Deck shall be Play-Tuff coated after fabrication. The UltraZip Deck Legs shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will have a multi-stage baked-on powder coat finish. The Split Collar Half shall be fabricated using 1/4" thick HR steel and will have a multi-stage baked-on powder coat finish. The UltraZip Beam Pin shall be fabricated using AISI 1045 cold drawn steel. The Hanger Pin shall be fabricated using AISI 303 stainless steel. The UltraZip Ramp shall be fabricated using punched, formed, and welded 12 gauge sheet steel and 2.875" O.D. sch. 40 pipe and shall be Play-Tuff coated after fabrication. The Grip Ramp Bracket shall be fabricated using precision cut and welded 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The Grip Ramp Foot shall be fabricated using precision cut 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap Bumper shall be fabricated using PN 579108 D-Shaped, O-Bore Bumper. R5-1362 - Steel Push-Out Wall The Steel Push-Out Wall shall be fabricated from 1.029" O.D. 14 gauge tubing and 1.315" O.D. 12 gauge tubing with welded on 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Push-Out Seat Panel, Push-Out Wall Round Event Panel, Pushout Seat & Supports shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bug Eye Bubble shall be constructed of 3/16" Clear Polycarbonate. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. R5-18030 - Orbital Shade The Orbital Shade - Post Connectors shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel brackets and tabs and shall have a powder coat finish. The Orbital Shade - Curved Extensions shall be fabricated using 5" O.D. 11 gauge steel tubing with a welded 1/4" thick steel cap and 3/8" thick steel brackets and shall have a powder coat finish. The Orbital Shade - Outside Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and a welded nut and shall have a powder coat finish. The Orbital Shade - Canopy Support Frames shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel tabs and shall have a powder coat finish. The Orbital Shade Canopy shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel tensioner. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5-1504 - Belt Bridge The Belt Bridge shall be made of 3-ply belt attached between two deck faces with a specialized steel clamp/bracket assembly. The Belt Bridge Walls shall be constructed of 1.315" O.D. 12 gauge tube steel outer rail with evenly spaced 1.029" O.D. 14 gauge tube steel inner rails welded horizontally and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1294 - Square Net Zipper The Square Net Zipper - Top Rope Guardrail shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/16" and 1/4" thick steel clevises and will be Powder Coated as specified. The Square Net Zipper - Hanger Rail shall be fabricated using 1-1/2" x 3" 11 gauge rectangular steel tubing with welded 3/16" and 1/4" thick steel clevises and will be Powder Coated as specified. The Square Net Zipper - Frames shall be fabricated using 1-1/2" x 3" 11 gauge rectangular steel tubing and 1.900" O.D. 11 gauge steel tubing with welded 3/16" and 1/4" thick steel clevises and 1/4" and 3/8" thick steel flanges and will be Powder Coated as specified. The Square Net Zipper - Rubber Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Square Net Zipper Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Square Net Zipper Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1230 - Clover Climber The Clover Climber shall be constructed of 1.900" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate. The Clover Climber will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC 2485 - Neutron Spinner The Neutron Spinner Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Neutron Spinner Ring shall be fabricated from a 2" square 11 gauge steel outer ring connected to a 5" O.D. 1/2" thick steel center housing by 1.900" O.D. 11 gauge steel spokes with 1/4" thick steel gussets and will be Powder Coated as specified. The Neutron Spinner Post shall be fabricated from a machined steel spindle mounted with 3/8" thick steel plates into a 5" O.D. 7 gauge steel post and will be Powder Coated as specified. The Neutron Spinner Dome Cap shall be precision die-cast from a high-strength aluminum alloy with a Ø7/16" center mounting hole and will be Powder Coated as specified. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2439-F - Tri Spring Deck - Fixed Mount The Tri Spring Deck shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and will be Play-Tuff™ coated after fabrication. The Fixed Mount Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with a 1/2" thick steel top mounting plate and will have a multi-stage baked-on powder coat finish. PC 2290 - Double Up & Over Climber The Double Up and Over Climber shall be fabricated from 1.900" O.D. 11 gauge Main Rails with 1.315" O.D. 12 gauge tube steel for the climbing rungs. The Double Up and Over Climber will be Powder Coated as specified. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1303 - Welcome Safety Sign The Welcome Safety Sign shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Sign Frame shall be 2.375" O.D. 11 gauge tube steel with welded on laser-cut steel brackets and will be Powder Coated as specified. The Sign Post shall be a 2x2 Sq. tube and will be Powder Coated as specified. 5203 - NFuse Tri-Ring Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket, Chain Surface Mount Weldment, & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Tri-Ring Bay - Inner & Outer Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Chain shall be 5/0 galvanized chain. The Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The NFuse Tri-Ring Bay - S-Plate shall be precision cut from 10 gauge stainless steel. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5102 - NFuse 2-Rung Access Ladder Frame The NFuse 2-Rung Access Ladder Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube, 1.315" O.D. 12 gauge steel tubing and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1949 - Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing welded to 1/4" reinforcer plates and a 3/8" top plate and will be Powder Coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Stand-N-Spin Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be Powder Coated as specified. The Stand-N-Spin Base & Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. The External Snap Ring shall be zinc and yellow chromate-plated steel and have an internal diameter of 2". 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1932 - Hand Spin Cycler The Hand Spin Cycler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1501-1502 - Arch Bridge The Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Arch Bridge Rails shall be fabricated using 1.660 O.D. 11 gauge steel tubing, 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with 1/4" HR Steel and 10 gauge HR Steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Arch Bridge Wall and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arch Bridge Wall Stiffener shall be made from 1-1/4" HR flat bar and 3/8" HR steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1414-1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1410 - Loop Traverse The Loop Traverse 90 Deg. Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab and will be Powder Coated as specified. The Loop Traverse 144" R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports, 1/2" thick steel tab, and 1/4" thick steel clevises and will be Powder Coated as specified. The Loop Traverse shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports with 1/4" thick steel clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1261 - Ebb & Flow Climber The Ebb & Flow Climber Frame, and Platform Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" and 3/16" thick steel clevises and 1.900" steel mount plugs and will be Powder Coated as specified. The Ebb & Flow Anchor Brackets shall be fabricated using 1/4" thick stainless steel and will be Powder Coated as specified. The Ebb & Flow Horizontal Strut shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/16" thick steel clevises and 1.900" steel mount plug pins and will be Powder Coated as specified. The Ebb & Flow Deck Plate shall be fabricated using 1/4" thick steel plating with welded 3/16" thick steel clevises and will be Powder Coated as specified. The Ebb & Flow Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connecters and machined aluminum ferrules. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1258 - Vertical Wave Climber The Vertical Wave Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing frame with 1.315" O.D. 12 gauge tube steel cross members and welded on Clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1257 - Access Climber The Access Climber shall be fabricated from 1.660" O.D. 11 gauge tube steel frame with 1.315" O.D. 12 gauge tube steel cross members and welded on Clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1249-DDH/DGH - GEO-WAVE CLIMBER HORIZONTAL The Geo-Wave Climber shall be constructed of UV-stabilized, rotationally molded, linear low-density polyethylene with an average double wall thickness of .250". The Geo-Wave Deck Mount Bracket shall be formed from 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 Gauge steel tubing with formed 1/4" thick end tab and will have a multi-stage baked-on powder coating. The Deck Filler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1219 - Deep Rung Arch Climber The Arch Climber Deep Rung shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.