PC-1906 - Thunder Wedge The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Wedge Step shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Thunder Wedge Net Frame, Thunder Wedge Window & Insert Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick sheet steel and ASAI 304 stainless steel anchors and will have a multi-stage baked-on powder coat finish. The Thunder Wedge Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Thunder Wedge Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing, 3/16" sheet steel and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Cargo Net Surface Mount Bracket shall be fabricated using 1/4" sheet steel plate with a 3/16" stainless steel clevis and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. 1690-CLR - Small Color Wheel The Small Color Wheel Front and Back Panels, Inner and Outer Hubs, and Color Chips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-ORCL - Small Oracle Panel The Small Oracle Panel, Arrow, Inner & Outer Hubs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-HYP - Small Hypno Station Panel The Small Hypno Station Axle, Holder, Handle, & Rotator shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-BBL - Small Bubble Panel The Small Bubble Panel Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bubble Panel shall be made from polycarbonate. 1690-TTT - Small Tic-Tac-Toe Panel The Small Tic-Tac-Toe Panel, Small Tic-Tac-Toe Trim, & Tic-Tac-Toe Piece shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1631 - Pin Ball Panel The Pinball Panel Mounting Ring, Rotator, Clamping Rings, & Deflectors shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Pinball Panel Window shall be made from .118 Polycarbonate sheet plastic. 1609 - Mirror Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mirror shall be fabricated from 16 gauge AISI 304 stainless steel sheet. 1605 - Clock Panel The Clock Panel, Large & Small Hand Panels shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1612 - Alphabet Maze Panel The Alphabet Maze Panel Round shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 18026 - Shade Canopy Hex The Roof Canopy Jack Screw shall be fabricated using 2"O.D.10ga Tube steel, 1" HR round bar, 10ga stainless steel, 10ga HR sheet steel and AISI 304 stainless steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Support Leg shall be fabricated using 2.5" sch 40 pipe, 2.375"O.D. 10ga galvanized T.S. and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter Hub shall be fabricated using 2.5" sch 40 pipe, 3/8" 1/2" weld nut and 1/2" hex nut and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter shall be fabricated using 2.375"O.D. 10ga galvanized T.S. and 1/2" HR sheet steel and will have a multi-stage baked-on powder coat finish. R5-12891-HEX - Center Access Climber-Hex The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck - Barrier shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 10 gauge HR sheet steel and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck - Handle and Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing, 3/8" HR sheet steel, 10 gauge HR sheet steel, 3/8" Tabs, and 3/16" Caps and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck - Ladder Leg shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The Center Access Hex Deck Ladder Deck Mount and Ladder Leg Surface Mount shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1405 - Horizontal Ladder Curved The Horizontal Ladder Curved shall be fabricated from 2.375" O.D. 10 gauge tube steel support beams with 1.315" O.D. 12 gauge tube steel rungs uniformly spaced and welded in place. The Horizontal Ladder Curved will be Powder Coated as specified. R5-1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS R5 1000 - Medallion on Post Assembly The Medallion shall be made from high density 3/4" sheet plastic specially formulated for optimum UV- Stability and color retention. The R5 Medallion Bracket shall be fabricated using punched and formed 12 gauge sheet steel and will be Powder Coated as specified. PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2457 - Bucket Spinner The Bucket Spinner shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bucket Spinner Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will be Powder Coated as specified. The Spinner Seat Hub shall be fabricated using a machined stainless steel hub with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. PC 1924 - Quad Teeter Totter The Seesaw Handle Bar Cap, Spacers, Oval End Cap and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Seesaw Seat shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Quad Teeter Totter Frame shall be fabricated using 3.5" O.D. 11 gauge steel frame, 2.375" O.D.11 gauge steel stand off, 1.900" O.D. 11 gauge steel posts and 1.315" O.D 12 gauge steel rests with welded 1/4" thick steel base, gussets, tabs and 10 gauge steel brackets and will be Powder Coated as specified. The Quad Teeter Totter Plate shall be precision laser cut from 3/8" thick steel and will be Powder Coated as specified. The Oval End Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will be Powder Coated as specified. PC 1056 - Lunar Rover The Lunar Rover Dash, Roof Brace & Seats shall be fabricated using punched, formed and welded 12 gauge sheet steel, reinforcing cross members, and gussets. The Decks & Steps shall be Play-Tuff(TM) coated after fabrication. The Lunar Rover Panels, Seats, & Tire Sets shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Lunar Rover Side Frame shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting tab and will be Powder Coated as specified. The Lunar Rover Front Frame shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3.5" O.D. 11 gauge steel tubing, 3/16" & 1/4" steel tabs and will be Powder Coated as specified. The Spring Rider Bracket & Castle Tab shall be precision laser-cut and formed from 3/16" thick sheet steel and will be Powder Coated as specified. The Drive Shifter shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Wheel Insert & Lunar Rover Accent Pieces shall be precision laser-cut from 14 gauge sheet steel and will be Powder Coated as specified. NF 5302 - NFuse Slither Climber Extension The Slither Climber Support Mount Bracket shall be punched and formed from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Slither Climber & Roto Plug shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Supports shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting bracket, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing, 1.029" O.D. 14 gauge steel tubing, and 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel clevises, 3/16" thick steel clevises, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. 5204 - NFuse Molecule Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment & NFuse Molecule Bay - Bottom/Top Outside Rails shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Inner /Top Nets & Deck Link Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The NFuse Molecule Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors, rotationally molded LDPE blocks, and machined aluminum end ferrules. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.