R5-1660-1669 - Panel Pal Roto R5 SMALL BELL: Shall be die-cast using 356.1 aluminum alloy and will have a multi-stage baked-on powder coat finish. HDPE PARTS (ALL): Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PANEL PAL ROTO FRAME: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PANEL PAL MIRROR STEEL: Shall be fabricated using 16 ga. 304 #8 HPSS. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1109 - Promenade/Balcony Deck PROMENADE & BALCONY DECKS R5 & R35: Shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play- Tuff™ coated after fabrication. PROMENADE WALL R5 & R35: Shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs, 1/4" thick steel clevises and 3/8" thick steel tabs, and will have a multi-stage baked on powder coat finish. BALCONY WALL R5 & R35: Shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 3/8" thick steel tabs, and will have a multi-stage baked on powder coat finish. BALCONY WINDOW R5 & R35: Shall be made from 1/2" polycarbonate and is to be replaced if damaged or discolored or within 4 years. GLASS SUPPORT R5 & R35: Shall be fabricated using punched 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. FRICTION WHEEL BRACKETS: Shall be fabricated using 12 gauge sheet steel with a multi-stage baked-on powder coat finish. FRICTION WHEEL: Shall be machined from 1-1/2" round UHMW plastic. SPINNER DISC: Shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. SPINNER HUB & SIGN: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. SPINNER AXLE: Shall be machined from 1" round mild steel with a welded 1/4" steel plate and will have a multi-stage baked-on powder coat finish. SPINNER PLATE: Shall be punched from 10 gauge sheet steel and will have a multi-stage baked-on powder coat finish. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1445-SEAT - UltraZip - Standard Seat The Pipe Plug shall be precision cut from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish as specified. The UltraZip Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The UltraZip Seat Rope shall be made from 24mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The UltraZip Seat Ferrule and Swivel Pin shall be machined from stainless steel. 1445 - UltraZip The UltraZip End Beam shall be extruded from a high strength aluminum alloy with a welded machined aluminum pin. The UltraZip Straight Beam shall be extruded from a high strength aluminum alloy. The UltraZip Coupler shall be precision cut and welded 1/2" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel tie plate and will have a multi-stage baked-on powder coat finish. The UltraZip Junction Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel plate and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap shall be fabricated from 3/8" steel and will have multi-stage baked-on powder coat finish. The UltraZip Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel. The UltraZip Deck shall be Play-Tuff coated after fabrication. The UltraZip Deck Legs shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will have a multi-stage baked-on powder coat finish. The Split Collar Half shall be fabricated using 1/4" thick HR steel and will have a multi-stage baked-on powder coat finish. The UltraZip Beam Pin shall be fabricated using AISI 1045 cold drawn steel. The Hanger Pin shall be fabricated using AISI 303 stainless steel. The UltraZip Ramp shall be fabricated using punched, formed, and welded 12 gauge sheet steel and 2.875" O.D. sch. 40 pipe and shall be Play-Tuff coated after fabrication. The Grip Ramp Bracket shall be fabricated using precision cut and welded 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The Grip Ramp Foot shall be fabricated using precision cut 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap Bumper shall be fabricated using PN 579108 D-Shaped, O-Bore Bumper. R5 12801 - Sunrise Climber R5 The Sunrise Climber R5 shall be fabricated using 1.315" O.D. 12 gauge steel rungs with welded 1.900" O.D. 11 gauge steel frame, 1/4" thick steel mounting plate and clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1222 - Snake Climber The Snake Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 1/4" thick steel mounting plate and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 1830 - Telescope On Wall The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Mounting Bracket shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Telescope Disc Spacer Wall and Mounting Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Telescope Lens Small and Large shall be fabricated using .118" thick Polycarbonate. The Telescope Swivel Bracket shall be 3-pieces precision laser-cut and welded together from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1803 STL - Steel Hex Roof The Steel Hex Roof Corner Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Hex Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1704 V2 - Poly Wave Single Slide V2 The Poly Wave Slide V2 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slide Leg & Footing shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1615 - Counter Assembly The Counter Assembly shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1221 - Chain Net Climber shall be constructed of 1.315" O.D. 12 gauge steel rungs affixed to 5/0 chain on 12" centers to form a complete chain net unit and will have a Play-Tuff(TM) coating. The Chain Net Foot shall be fabricated of 1/4" thick steel bent 90° with welded on rebar extensions and will be Powder Coated as specified. The Optional Handrails shall be made from 1.315" O.D. tube steel and welded into the appropriate shape and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1110 1117 ALU - Vertical Deck Filler The Vertical Deck Fillers shall be fabricated from .120" sheet aluminum. The Vertical Deck Fillers will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1103 - Half Hex Deck 5 Post Assembly The Half Hex Deck 5 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.