RV 21263 - Launch Pad Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 21000 - Revolution Post Top Cap The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified. RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. RV 1437 - Tri-Pad Jungle Traverse 90 Degree RV The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tri-Pad Jungle Traverse 90° Top Frame RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets, 3/16" thick stainless steel anchors, and stainless steel pin and shall have a powder coat finish. The Tri-Pad Jungle Traverse Vine shall be made from 16mm steel-reinforced rope with machined aluminum end clevises. The Tri-Pad Jungle Traverse Station shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and 3/16" thick stainless steel anchor and shall have a powder coat finish. The Tri-Pad Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tri-Pad Support Sleeve shall be fabricated using 2" O.D. 10 gauge stainless steel tubing. R35 1936 - Ring Pull Up The Ring Pull-Up shall be 1-1/2" x 3" tubing designed to attach the complete unit to upright posts and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R35 1301 - R3.5 Wall Assembly The R3.5 Wall shall be made from high-density, 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC-2488 - Tidal Wave The Tidal Wave Seat Middle and End shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tidal Wave Frame Sections Middle and Ends Shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff (TM) coated after fabrication. The Tidal Wave Center Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 1/4" HR Sheet Steel Tidal Wave Center Post Base, 10 gauge HR Sheet Steel Tidal Wave Center Leg Gussets, a 10 gauge HR Sheet Steel Torsion Spring Shroud 120 and a 3.5" x .1875" Wall Square Tubing Housing and will be Powder Coated as specified. The Tidal Wave End Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 3.5" x .1875" Wall Square Tubing Housing, a 10 gauge HR Sheet Steel Torsion Spring Shroud 200, 1/8" HR Strip Steel Tidal Wave End Leg Caps and a Steel Tidal Wave End Pivot Axle and will be Powder Coated as specified. The Torsion Spring Mount shall be bent and formed from 1/4" HR Sheet Steel and will be Powder Coated as specified. The Tidal Wave End Pivot Base Weldment shall be made of punched and formed 1/4" HR Sheet Steel and a Steel Tidal Wave Pivot Bearing Sleeve and will be Powder Coated as specified. The Tidal Wave End Post Base Plates shall be precision laser cut from 1/4" HR Sheet Steel. The Tidal Wave End Post Base Plates will be Powder Coated as specified. The Torsion Spring Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. NF 5302 - NFuse Slither Climber Extension The Slither Climber Support Mount Bracket shall be punched and formed from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Slither Climber & Roto Plug shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Supports shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting bracket, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing, 1.029" O.D. 14 gauge steel tubing, and 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel clevises, 3/16" thick steel clevises, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. 5201 - NFuse Hex Net Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bottom Weldment shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Bracket shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside & Top Outside Weldment shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 21264 MNT - Angled Landing Pad to Mount RV The Angled Landing Pad to Mount Frame RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge handles, stainless steel housing and 1/4" thick steel brackets and will be Powder Coated as specified. The Landing Pad shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. 4250 - Rectangular Picnic Table The Table Top & Bench shall be fabricated from punched, formed, and welded 14 gauge sheet steel and shall be Play Tuff(TM) coated after fabrication. The Table Frame Brace shall be fabricated from punched and formed 10 gauge sheet steel and shall have a powder coat finish. The Table Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounts and shall have a powder coat finish. The Frame Support shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1930 - Chinning Bar The Chinning Bar R5 & R35 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and shall have a powder coat finish. The Chinning Bar R5 Hybrid & RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting brackets and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1261 - Ebb & Flow Climber The Ebb & Flow Climber Frame, and Platform Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" and 3/16" thick steel clevises and 1.900" steel mount plugs and will be Powder Coated as specified. The Ebb & Flow Anchor Brackets shall be fabricated using 1/4" thick stainless steel and will be Powder Coated as specified. The Ebb & Flow Horizontal Strut shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/16" thick steel clevises and 1.900" steel mount plug pins and will be Powder Coated as specified. The Ebb & Flow Deck Plate shall be fabricated using 1/4" thick steel plating with welded 3/16" thick steel clevises and will be Powder Coated as specified. The Ebb & Flow Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connecters and machined aluminum ferrules. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.