R5-1660-1669 - Panel Pal Roto R5 SMALL BELL: Shall be die-cast using 356.1 aluminum alloy and will have a multi-stage baked-on powder coat finish. HDPE PARTS (ALL): Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PANEL PAL ROTO FRAME: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PANEL PAL MIRROR STEEL: Shall be fabricated using 16 ga. 304 #8 HPSS. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. PC-4232 - SpringMax Turbo Totter TURBO TOTTER DECK: Shall be fabricated using punched and welded 12ga sheet steel and will be Play-Tuff™ coated after fabrication. TURBO TOTTER FRAME: Shall be fabricated using 2.375" O.D.10ga, 1.900" O.D. 11ga, 1.660" O.D. 12ga and 1.315" O.D. 12ga steel tubing with 3/8" and 1/4" sheet steel gussets, plates and tabs with 3/16" pipe plugs and will have a multi-stage baked-on powder coat finish. TURBO TOTTER LEG: Shall be fabricated using 6"x6"x.25" square tube steel with a 1/2", 3/8" and 1/4" sheet steel gussets, and plate and will have a multi-stage baked-on powder coat finish. BUMPER MOUNT: Shall be fabricated using 2.375" O.D.10ga steel tubing with 3/8" sheet steel plate and 1/4" sheet steel gussets, with 1/2" sq weld nuts and will have a multi-stage baked-on powder coat finish. TURBO TOTTER SEAT SPACER & TURBO TOTTER RUBBER STRIP SPACER: Shall be made from high density 3/4" sheet plastic specially fomulated for optimum UV stability and color retention. SPRING FLING HANDLE: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". TURBO TOTTER SEAT & TURBO TOTTER RUBBER STRIP: Shall be constructed of UV-stabilized flexible rubber compound. TURBO TOTTER BUMPER: Shall be molded black rubber, durometer 68A. TORSION SPRING: Will be an assembly consisting of a machined shaft surrounded by rubber extrusions enclosed in a metal housing. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1850 - Arc Post Topper The Arc Post Topper R35/R5 shall be fabricated using 3.5" or 5" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1362 - Steel Push-Out Wall The Steel Push-Out Wall shall be fabricated from 1.029" O.D. 14 gauge tubing and 1.315" O.D. 12 gauge tubing with welded on 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Push-Out Seat Panel, Push-Out Wall Round Event Panel, Pushout Seat & Supports shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bug Eye Bubble shall be constructed of 3/16" Clear Polycarbonate. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. RV 21260/21263 - Launch Pad Seat and Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 21000 - Revolution Post Top Cap The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified. RV 16101 - Round Roto Panel RV The Roto Panel Arm RV shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Roto Panel Leg RV shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Round Roto Panel RV shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 12012 - 2' Climb-N-Slide RV The Inside & Outside Slide Climber Rails RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing welded 1/4" thick steel mounting brackets and 10 gauge thick steel tabs and will be Powder Coated as specified. The Slide Climber Support Legs RV shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge thick steel tabs and will be Powder Coated as specified. The Slide Climber RV shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Single Slide Leg 24" - 36" V23 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 3/16" thick steel plate and will be Powder Coated as specified. The 2' Poly Wave Slide Vers2 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV-1971 - Rumble Deck RV The Multi-Spring Deck Mounting Plate shall be precision cut using 1/4" thick plate steel and will have a multi-stage baked-on powder coat finish. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will have a multi-stage baked-on powder coat finish. The Rope Clevis shall be fabricated using precision cut and formed 3/16" thick plate steel. The Rumble Deck Frame shall be fabricated using punched, formed and welded 12 gauge sheet steel and will be Play-Tuff™ coated after fabrication. The Rumble Deck Rope shall be made from 16mm steel reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick plate steel and will have a multi-stage baked-on powder coat finish. The Tri Spring Deck shall be fabricated using punched and welded 12 gauge sheet steel and will be Play-Tuff™ coated after fabrication. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. RV 1959 - Tri Ring Hub RV The Tri-Ring Hub Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Tri-Ring Hub Rail with Mounts RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails, 1/4" thick stainless steel mounting brackets, and stainless steel pins and will be Powder Coated as specified. The Post Tab Bracket RV shall be fabricated from 1/4" thick stainless steel mounting bracket with welded 3/8" thick steel tab and will be Powder Coated as specified. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250", and .375" thick molded in aluminum mounting plates. RV-1524 - Bobble Bridge RV The Bobble Bridge shall be made from punched and formed 12 gauge sheet steel with welded 12 gauge sheet steel side members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Bobble Bridge Inside Trim & Side Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bobble Bridge Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end clevises. The Bobble Bridge Rail shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.660" O.D. 11 gauge support rail, 1.315" O.D. 12 gauge center rail, 1/4" thick steel mounting brackets and 3/16" thick steel anchors and will be Powder Coated as specified. The Chain shall be 5/0 galvanized low carbon steel chain with silver shield finish. The Rope Bridge Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. RV 1437 - Tri-Pad Jungle Traverse 90 Degree RV The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tri-Pad Jungle Traverse 90° Top Frame RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets, 3/16" thick stainless steel anchors, and stainless steel pin and shall have a powder coat finish. The Tri-Pad Jungle Traverse Vine shall be made from 16mm steel-reinforced rope with machined aluminum end clevises. The Tri-Pad Jungle Traverse Station shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and 3/16" thick stainless steel anchor and shall have a powder coat finish. The Tri-Pad Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tri-Pad Support Sleeve shall be fabricated using 2" O.D. 10 gauge stainless steel tubing. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1536 - 180 Degree Crawl-Netix Climbers The Crawl-Netix Flange Stiffeners/Support Arm Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net/Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net Sections shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail Sections shall be fabricated using 1.029" O.D. 14 gauge and 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and steel clevises and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Split Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Bottom Support Arm shall be fabricated using 1.900" O.D. 11 gauge, 2.375" O.D. 11 gauge, and 2.875" O.D. schedule 40 steel tubing with welded 1/4" thick steel plate and clamps and will be Powder Coated as specified. The Crawl-Netix Tube Clamp shall be fabricated using 3/16" thick sheet steel with a welded steel ball bearing and will be Powder Coated as specified. The Ball Joint Socket shall be machined from UHMW plastic. R5 1535 - Crawl-Netix Climber R5 The Crawl-Netix Flange Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Roto Panel Leg shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 3/16" thick bracket, and a 1/4" thick steel plate and will be Powder Coated as specified. The Roto Round Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2472 - Spin-Max Orbit The Spin-Max Cover Halves, Support Cap & Steps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Spin-Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin-Max Orbit Cross Supports shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" tabs and clevises and will be Powder Coated as specified. The Spin-Max Orbit Main Support Tubes shall be fabricated using 1.5" x 3" 11 gauge rectangular steel tubing with welded 2" x 2" x 1/4" thick square steel tubing and welded 1/4" thick steel clevises, 1/4" thick steel plate, 12 gauge steel caps, and steel plug and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Orbit Support Leg shall be fabricated using 5" schedule 80 pipe with welded 3/8" thick steel mounting plate and gussets and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Spin-Max Orbit Ropes shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Hex Net Rubber Plug Top & Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 1/4" plates and plug, 3/8" thick steel plates, and machined steel spindle and will be Powder Coated as specified. The Spin-Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will Powder Coated as specified. The Spin-Max Base Spacer shall be machined from high strength aluminum. PC 2181 - Single Post Swings The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. NF-5206 - NFuse Explorer's Arch Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Top Rail & NFuse Molecule Bay - Bottom Rail shall be fabricated using 2.375" O.D. steel tubing with welded 1/4" thick steel clevises and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Side Rail shall be fabricated using 1.900" O.D. steel tubing with welded 1/4" thick steel clevises and 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Extension Frame shall be fabricated using 1-1/2" x 3" x .120" Rectangular TS, welded 1/4" thick steel plates and clevises, 3/16" thick stainless steel clevises and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Ladder shall be fabricated using 2.375" O.D., 1.900" O.D. and 1.315" O.D. steel tubing with welded 1/4" thick steel plates and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The Round Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The NFuse Explorer's Arch Bay - Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The NFuse Explorer's Arch Bay - Back Rest shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The NFuse Explorer's Arch Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The Roto Panel Net Bracket shall be fabricated using 3/16" thick steel bracket with welded 3/16" thick steel clevis and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 21011 MNT - Revolution Beam Mid-Support The Revolution Beam Mid-Support shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded stainless steel housing and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1110 1117 STL - Vertical Deck Filler The Vertical Deck Fillers shall be made from 12 Gauge sheet steel and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.