1710-SUP - Twister Slide Support Assembly The Sectional Slide Support Bracket #2 shall be fabricated using 3/16"HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support shall be fabricated using Ø1.660 steel tubing, 3/16" HR sheet steel and 5/8"round bar and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Top shall be fabricated using Ø2.000 steel tubing and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Bottom shall be fabricated using Ø1.660 steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1707-5 - Tube Slide 5 Section 60" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1214 - Climbing Wall The Chain Mount Bracket shall be laser-cut 1/4" thick steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Climb Chain Hanger shall be laser-cut 3/8" thick plate steel. The Climb Chain Hanger shall have clear zinc plating. The Grip Climb Wall shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Grip Climb Wall Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish and shall be Play-Tuff(TM) coated. The Grip Climb Wall Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 1.315" O.D. 12 gauge steel cross member with welded 3/8" thick steel tab and will be Powder Coated as specified. The Grip Ramp Bracket shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. The Ramp Grips shall be precision die-cast from a high strength aluminum alloy and shall have a thermoplastic coating. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4331 - Urban Elite Bench The Elite Bench Back & Seat shall be fabricated using punched, formed and welded 14 gauge and 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Bench Inground Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and will be Powder Coated as specified. The Bench Surface Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and 3/16" thick steel mounting plates and will be Powder Coated as specified. PC 4221 - Pedestal Picnic Table The Pedestal Seat Frame Mount shall be fabricated using 1.5" x 3" x 0.120" steel tubing with welded 2.375" O.D. 11 gauge steel Mounting Rail, 12 gauge sheet steel End Cap, 1/4" thick steel Mounting Plate, and 10 gauge sheet steel Support Brackets and will be Powder Coated as specified. The Pedestal Table shall be fabricated using punched, formed and welded 14 gauge sheet steel. The Pedestal Table shall be Play-Tuff(TM) coated after fabrication. The Pedestal hardware Pin shall be machined from stainless steel round bar. The Picnic Table Pedestal shall be fabricated using 4" x 0.25" square steel tubing with welded 2.375" O.D.11 gauge steel supports,10 gauge sheet steel Support Brackets, and 12 gauge steel End Cap and will be Powder Coated as specified. The Table Seat shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The 3/8" x 2" S Plate shall be precision laser cut from 1/4" HR sheet steel and will be Powder Coated as specified. PC 4218 - Trash Receptacle The Trash Receptacle Body & Lid shall be fabricated using punched and formed 14 gauge sheet steel and shall be Play-Tuffâ„¢ coated after fabrication. The Trash Receptacle Dome Lid shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Trash Receptacle In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting plate and will have a multi-stage baked-on powder coat finish. The Trash Receptacle Lanyard shall be constructed of vinyl-coated galvanized steel wire and high strength aluminum oval sleeves. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.