1298 - Cord Climber CORD CLIMBER TOP BAR: Shall be fabricated using 2.375" OD 10ga T.S., 1/4" HR sheet steel, 3/16" HR sheet steel, 3/8" HR sheet steel and AISI 304 stainless steel and will have a multi-stage baked on powder coat finish. CLIMBING ROPE: Shall be made from 24mm steel-reinforced woven rope with machined aluminum end ferrules. CLIMBING ROPE BALL: Shall be made from GEZOFLEX 0.5-1.5 EPDM rubber. CHAIN: Shall be fabricated from 7mm galvanized steel chain. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1710-SUP - Twister Slide Support Assembly The Sectional Slide Support Bracket #2 shall be fabricated using 3/16"HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support shall be fabricated using Ø1.660 steel tubing, 3/16" HR sheet steel and 5/8"round bar and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Top shall be fabricated using Ø2.000 steel tubing and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Bottom shall be fabricated using Ø1.660 steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5-1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1289 - Cliffhanger Climber The Cliffhanger Climber shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/2" thick steel tabs and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel handle and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails, 1/4" thick steel mounting clevises, 1/4" thick steel tabs, and 1/2" thick steel tab and will have a multi-stage baked-on powder coat finish. The Promenade Deck shall be fabricated using punched, formed, and welded 12 gauge sheet. The Promenade Deck shall be Play-Tuff(TM) coated after fabrication. The Socket Clamps & Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1281 - Arch Twist Climber The Arch Twist Climber shall be 1.315" O.D. 12 gauge steel rungs, spokes and upper rail welded to 1.900" O.D. 11 gauge steel outer hub and lower rail with 1/4" steel clevises for mounting and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1243 - Disc Pole Climber The Disc Pole Climber Half Disc shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Disc Pole Climber Poles shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified.