R5-15111 - Inclined Jumbo Rope Link STEEL TUBING WELDMENT: Shall be fabricated using 1.660 O.D. 11ga tube steel, 1.315 O.D. 11ga. tube steel with 1/4" sheet steel, AISI 304 stainless steel clevises and will have a multi-stage baked on powder coat finish. JUMBO ROPE MOUNT BRACKET: Shall be fabricated using cut and welded 1/2" and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. INCLINED JUMBO ROPE: Shall be made from 140mm polyproppylene rope w/steel core, stainless steel bands, buckles and cable thimble and aluminum crimp sleeves. INCLINED JUMBO ROPE 24" NET: Shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 12091 - Inclined Belt Climber PEDESTAL TRANSFER DECK: Shall be fabricated using punched, formed and welded 12 gauge A36 sheet steel with 1/2-13 threaded steel rod and shall be Play-Tuff™ coated after fabrication. TRANSFER BELT HANGER: Shall be fabricated using punched, formed and welded 12 gauge A36 sheet steel and shall be Play- Tuff™ coated after fabrication. LOOP CLIMBER 270º PLATE: Shall be fabricated using 3/16" A36 sheet steel and will have a multi-stage baked-on powder coat finish. BELT CLIMBER RAIL 48" LEFT & RIGHT: Shall be fabricated using 1.660 OD 11 gauge tube steel with 1/4" A36 sheet steel and 5/8" round bar and will have a multi-stage baked on powder coat finish. PEDESTAL TRANSFER DECK LEG: Shall be fabricated using 5" OD 7 gauge tube steel with 3/8" A36 sheet steel and will have a multi-stage baked on powder coat finish. BELT: Shall be made from 5/16' thick 3 ply reinforced rubber sheet. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 5303 - NFuse Snake Net Extension The NFuse Snake Net Extension - Frame Rail Ground Mount and Surface Mount shall be fabricated using 1-1/2" x 3" rectangle tube, Ø1.315" OD tube steel, 1/4" HR sheet steel and AISI 304 Anchor Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" stainless steel. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 18093 - Tree House Shed Roof The Tree House Shed Roof shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 18031 - Corrugated Hex Roof The Braces, Roof Sections & Ridge Caps shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Steel Hex Roof Cap shall be fabricated using punched, formed and welded 14 gauge sheet steel and will be Powder Coated as specified. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Roof Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 13011 - Half Square Deck Steel Wall R5 The Half Square Deck Steel Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with a welded 1/4" thick steel tab and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1847 - Tree Top Roto R5 The Tree Top Roto R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1707 8 SP - Spiral Tube Slide 96" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1677 - Tree House Panel Assembly The Panels, Spacer, Plug & Counter shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Panel & Spring Rider Bracket shall be precision laser-cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Tree House Access Handle & Sit Down Side Guard shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Tree House Panel Trim & Window Trim shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Roto Panel Lug shall be machined from high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1126 - Center Access Hex Deck The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck Barrier and Handle shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. NF-5301 - NFuse Hex Net Extension The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Extension - Frame Rail shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing with welded 5/8" steel anchor, 1/4" thick steel clevis, and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Frame Rail - Surface Mount shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing with welded 1/4" thick steel anchor plate, 1/4" thick steel clevis, and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. 5204 - NFuse Molecule Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment & NFuse Molecule Bay - Bottom/Top Outside Rails shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Inner /Top Nets & Deck Link Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The NFuse Molecule Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors, rotationally molded LDPE blocks, and machined aluminum end ferrules. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1910 - Talk Tube The Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen and 1/4" thick steel tabs and will be Powder Coated as specified. The Steel Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing and 5" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen, 3/16" thick steel reducer/flanges, 5/8" round bar steel, and 1/4" thick steel tabs and will be Powder Coated as Specified. The Talk Tube Cone shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Socket Clamp shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1528 - Angled Net Link The 16-Link Galvanized Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Angled Net Link shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel anchors and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1215 - Inclined Grip Wall The Chain Mount Bracket shall be laser-cut 1/4" thick steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Climb Chain Hanger shall be laser-cut 3/8" thick plate steel. The Climb Chain Hanger shall have clear zinc plating. The Grip Climb Wall shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Grip Climb Wall Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish and shall be Play-Tuff(TM) coated. The Grip Ramp Bracket shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. The Ramp Grips shall be precision die-cast from a high strength aluminum alloy and shall have a thermoplastic coating. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1122 - Double Slide Deck Extension The Double Sit Down Extension Wall shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel guard rails, slide insert, and 1/4" thick steel clevises and will be Powder Coated as specified. The Tri-Deck Extension shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.