R5 1807 - Poly Shingled Roof The Poly Shingled Roof shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 1910 - Talk Tube The Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen and 1/4" thick steel tabs and will be Powder Coated as specified. The Steel Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing and 5" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen, 3/16" thick steel reducer/flanges, 5/8" round bar steel, and 1/4" thick steel tabs and will be Powder Coated as Specified. The Talk Tube Cone shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Socket Clamp shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 1704 V2 - Poly Wave Single Slide V2 The Poly Wave Slide V2 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slide Leg & Footing shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel plate and will be Powder Coated as specified. 1216 - Grip Climber The Grip Climber shall be fabricated from punched and formed 12 gauge sheet steel with a punched hole pattern to provide a variety of attachment points for climbing grips and shall be Play-Tuff(TM) coated after fabrication. The Grip Ramp Bracket shall be two-part laser-cut and welded from 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel. The Grip Ramp Foot shall have a multi-stage baked-on powder coat finish. The Climbing grips shall be one-piece 2-hole and 3-hole precision die-cast from a high strength aluminum alloy and will have a Thermal Plastic Coating. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.