RV 21260/21263 - Launch Pad Seat and Step RV 
 	The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250".

RV 21004 - Single Arm Event Hanger 
 	The Event Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support rail, 1/4" thick stainless steel mounting brackets and welded stainless steel pin and/or house and will be Powder Coated as specified. The Event Hanger Caps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention.

RV 21000 - Revolution Post Top Cap 
 	The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified.

RV 10000 - Revolution Post 
 	The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation.

RV 1968 - Warp Rung Wall RV 
 	The Warp Rung Wall RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Warp Rung Wall 1 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, and 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Warp Rung Mall 2 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and stainless steel housings and will be Powder Coated as specified.

RV 1967 - U-Loop Traverse RV 
 	The U-Loop Traverse RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 1.029" O.D. 14 gauge steel supports and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The U-Loop Traverse 1RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 1.029" O.D. 14 gauge steel supports, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The U-Loop traverse 2RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 1.029" O.D. 14 gauge steel supports and stainless steel housings and will be Powder Coated as specified.

RV 1959 - Tri Ring Hub RV 
 	The Tri-Ring Hub Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Tri-Ring Hub Rail with Mounts RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails, 1/4" thick stainless steel mounting brackets, and stainless steel pins and will be Powder Coated as specified. The Post Tab Bracket RV shall be fabricated from 1/4" thick stainless steel mounting bracket with welded 3/8" thick steel tab and will be Powder Coated as specified. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250", and .375" thick molded in aluminum mounting plates.

RV 1435 - Arch Loop Traverse RV 
 	The Arch Loop Traverse RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Arch Loop Traverse 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Arch Loop Traverse 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops and stainless steel housings and will be Powder Coated as specified.

RV 1419 - Tri-Pad Traverse RV 
 	The Disc Traverse Beam RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Disc Traverse beam 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Disc Traverse Beam 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs and stainless steel housings and will be Powder Coated as specified. The Disc Traverse Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Tri-Pad Traverse Station shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 3/8" thick steel tabs and will be Powder Coated as specified. The Tri-Pad Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. the Tri-Pad with Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Traverse U-Joint shall be stainless steel to resist rust and corrosion.

RV 1404 - Access Ladder RV 
 	The Access Ladder RV shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, rungs,and 1/4" thick steel mounting bracket nad will be Powder Coated as specified.

RH-21004 - Single Arm Event Hanger Hybrid 
 	The Event Hanger RH shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel clevis and stainless steel pin and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified.

R5 1309 - Half Wall (Handle) Assembly 
 	The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified.

R5 1306 - Double Sit Down Slide Hood 
 	The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified.

R5 1303 TW - Twister Entry Panel w/ Sit Down Hood 
 	The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified.

R5 1100 - Deck Identification 
 	NO SPECIFICATIONS

PC 131410 - Inclusive Swing Seat Assembly 
 	Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention.

PC-2985 - Rainbow Twist Climber 
 	The Rainbow Twist Climber shall be fabricated using 2.375" O.D. 11 gauge steel rails with welded 1.315" O.D. 12 gauge steel rungs. The Rainbow Twist Climber will be Powder Coated as specified. The Rainbow Twist Climber Leg shall be formed and fabricated using 2.375" O.D. 11 gauge steel tubing with welded 5/8" O.D. steel anchor. The Rainbow Twist Climber Leg will be Powder Coated as specified.

PC 2181 - Single Post Swings 
 	The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts.

18021 - Shade Canopy Square Roof 
 	The Roof Canopy Jack Screw shall be fabricated using 2" O.D. 10 gauge steel tube with welded 3/16" thick steel plugs, welded 1" O.D. machined steel retainer stub, 1" O.D. 11 guage steel cable spacer and punched 10 gauge steel retainers and will be Powder Coated as specified. The Roof Canopy Square Rafter Hub shall be fabricated using 2.50" O.D. schedule 40 pipe with welded zinc nut and stainless steel stop and will be Powder Coated as specified. The Roof Canopy Square Rafter shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel plug and will be Powder Coated as specified. The Roof Canopy Support Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to a formed 3/16" thick steel cradle and will be Powder Coated as specified. The Shade Canopy Square shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. The 1/4" Canopy Wire Cable shall be Ø1/4" steel cable with a clear vinyl coating.

1962 - Play Seat 
 	The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified.

1710 - Twister Slide 
 	The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified.

1702 - Double Slide 
 	The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified.

1285 MNT - Angled Terra Climber to Mount RV 
 	The Angled Terra Climber Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel  handles and stainless steel housing and will be Powder Coated as specified. The Angled Terra Climber Panel & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Grips shall be two-part and precision die-cast from a high strength aluminum alloy and shall be Play-Tuff(TM) coated after fabrication.

1277 MNT - Angled Lunar Climber to Mount RV 
 	The Angled Bubble Climber Panel & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Angled Bubble Climber to Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and stainless steel housing and will be Powder Coated as specified.

1233 - Disc Climber 
 	The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified.

1225 - Wave Climber 
 	The Wave Climber shall be fabricated from Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and will have a multi-stage baked-on powder coat finish. The Wave Climber Half Wall shall be fabricated from Ø 1.315" 12 gauge steel tubing and welded Ø 1.029" 14 gauge steel vertical rail, 1/4" steel plate and 1/4" steel tab and will have a multi-stage baked-on powder coat finish.

1209 - Transfer Station 
 	The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified.

1206 - ADA Steps with Walls 
 	The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM)  coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified.

1101 - Square Deck Assembly 
 	The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.