PC-2497 - Celebration Spinner CELEBRATION SPINNER BENCH TOP & BENCH ACCENT: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. CELEBRATION SPINNER BENCH RAIL : Shall be fabricated using 1.660" OD 11ga. tube steel,1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi-stage baked on powder coat finish. CELEBRATION SPINNER RAIL: Shall be fabricated using 1.660" OD 11ga. tube steel,1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi-stage baked on powder coat finish. CELEBRATION SPINNER HANDLE: Shall be fabricated using 1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi- stage baked on powder coat finish. CELEBRATION SPINNER UPRIGHT BEAM: Shall be fabricated using 1.5"X3"X.120 rect. tube steel with 1/4" and 12ga. sheet steel and will have a multi-stage baked on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1445-INC - UltraZip Inclusive Seat The Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Ultrazip ADA Swing Hanger shall be fabricated using à1.660" O.D. steel tubing and AISI 1018 stainless steel and will have a multi-stage baked-on powder coat finish. The Chain shall be 7mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. 11021 - Spiral Deck The 8" Rise Filler 8" shall be fabricated from punched 5052 sheet aluminum and will have a multi-stage baked-on powder coat finish. The Spiral Deck shall be fabricated using punched and formed 12 gauge sheet steel and will be Play-Tuff ™coated after fabrication. The Spiral Deck Half Wall R5 shall be fabricated from 1.315" O.D. 12 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Spiral Deck Wall shall be fabricated from 1.315" O.D. 12 gauge steel tubing, 1.029" O.D. 14 gauge steel tubing, and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5501 - NFUSE NIMBLE BAY BRIDGE The Socket Clamp Rope Clevis shall be fabricated from 3/16" thick stainless steel. The Angled Net Link Deck Connector & Nfuse Hex Net Bay Brackets shall be fabricated from 1/4" thick steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Nfuse Hex Net Bay Top Inside Weldment shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Ladder shall be fabricated from 2.375" O.D. 11 gauge and 1.315" O.D. 12 gauge steel tubing with welded 3/16" thick stainless steel clevises and machined ferrules and will have a multi-stage baked-on powder coat finish. The Bay Bridge Outside Rail shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick stainless steel clevises and 1/4" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Support Legs shall be fabricated from 1-1/2"x3"x.120" steel tubing with welded 12 gauge, 3/8", and 3/16" thick steel caps, tabs, and clevises and 5/8" O.D. anchors and will have a multi-stage baked-on powder coat finish. The Bay Bridge Support Leg Stiffeners shall be fabricated from 2.375" O.D. 11 gauge steel tubing with welded 1/4", 3/8", and 3/16" thick steel caps, tabs, and clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Side Rail shall be fabricated from 2.375" O.D. 11 gauge steel tubing with welded 3/8" and 3/16" thick steel tabs and clevises and machined ferrules and will have a multi-stage baked-on powder coat finish. The Bay Bridge Top Rail shall be fabricated from 3.5" O.D. 11 gauge steel tubing with 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. The Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Nimble Bay Bridge Net shall be made from 20mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Nfuse Curved Swage R35 Shade Post shall be fabricated from 3.5" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. 1980 - Counter Connection Assembly The Counter Connection Top shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Counter Connection Frame shall be fabricated using 1.5" x 3" rectangle tube with welded 12 gauge steel end caps and will have a multi-stage baked-on powder coat finish. The Counter Connection Leg shall be fabricated using 2.375" O.D. 11 gauge round tube, 1/4" HR sheet steel and 5/8" O.D. round bar and will have a multi-stage baked-on powder coat finish. The Counter Connection Post Mount shall be fabricated using 2.375" O.D. 11 gauge round tube and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1685-RND - Mosaic Panel Round The Mosaic Panel Round and Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mosaic Blocks shall be made from injection molded plastic. The Activity Panel Tube shall be fabricated from 0.924" O.D. galvanized steel tubing. 1690-CLR - Small Color Wheel The Small Color Wheel Front and Back Panels, Inner and Outer Hubs, and Color Chips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-RMKR - Small Rain Maker Panel The Small Rain Maker Back Panel, Rain Maker Cover, Rain Maker Rotator, Spinner Hub, and Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Rain Maker Window shall be made from .118 Polycarbonate sheet. 1414-C - Clover Seat The Spinner Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Clover Seat Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will have a multi-staged baked-on powder coat finish. The Clover Seat Leg Surface Mount shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 1/4" and 3/16" thick steel mounting plates with 10 gauge sheet steel gussets and will have a multi-staged baked-on powder coat finish. 5303 - NFuse Snake Net Extension The NFuse Snake Net Extension - Frame Rail Ground Mount and Surface Mount shall be fabricated using 1-1/2" x 3" rectangle tube, Ø1.315" OD tube steel, 1/4" HR sheet steel and AISI 304 Anchor Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" stainless steel. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1644-RND - Gear Panel Round The Gear Panel Components shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Gear Panel Windows shall be made from .118 Polycarbonate sheet plastic. 1690-ORCL - Small Oracle Panel The Small Oracle Panel, Arrow, Inner & Outer Hubs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-HYP - Small Hypno Station Panel The Small Hypno Station Axle, Holder, Handle, & Rotator shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-BBL - Small Bubble Panel The Small Bubble Panel Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bubble Panel shall be made from polycarbonate. 1690-BELL - Small Bell & Hammer Panel The Small Bell and Hammer Panel & Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bell shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-CHM - Small Chime Panel The Chime Panels & Chime Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Chime Panel Hubs & Spacers shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Chimes shall be fabricated using 0.75" Galvanized EMT 18ga and will have a multi-stage baked-on powder coat finish. The Chime Panel Bracket shall be punched and formed using 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. 1690-TTT - Small Tic-Tac-Toe Panel The Small Tic-Tac-Toe Panel, Small Tic-Tac-Toe Trim, & Tic-Tac-Toe Piece shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-3ROW - Small 3-in-a-Row Panel The Panel, Slider, & Stop shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1631 - Pin Ball Panel The Pinball Panel Mounting Ring, Rotator, Clamping Rings, & Deflectors shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Pinball Panel Window shall be made from .118 Polycarbonate sheet plastic. 1609 - Mirror Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mirror shall be fabricated from 16 gauge AISI 304 stainless steel sheet. 1634 - Labyrinth Panel The Pin Ball Panel Mounting Ring, Labyrinth Panel Rotator, & Labyrinth Panel Front & Back Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Labyrinth Window shall be made from .118 thick polycarbonate sheet plastic. 1630 - Hour Glass Panel The Pin Ball Panel Mounting Ring, Hour Glass Rotator, & Pin Ball Clamping Rings shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Hourglass Window shall be made from .118 thick polycarbonate sheet plastic. 1605 - Clock Panel The Clock Panel, Large & Small Hand Panels shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1612 - Alphabet Maze Panel The Alphabet Maze Panel Round shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 18026 - Shade Canopy Hex The Roof Canopy Jack Screw shall be fabricated using 2"O.D.10ga Tube steel, 1" HR round bar, 10ga stainless steel, 10ga HR sheet steel and AISI 304 stainless steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Support Leg shall be fabricated using 2.5" sch 40 pipe, 2.375"O.D. 10ga galvanized T.S. and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter Hub shall be fabricated using 2.5" sch 40 pipe, 3/8" 1/2" weld nut and 1/2" hex nut and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter shall be fabricated using 2.375"O.D. 10ga galvanized T.S. and 1/2" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1445 - UltraZip The UltraZip End Beam shall be extruded from a high strength aluminum alloy with a welded machined aluminum pin. The UltraZip Straight Beam shall be extruded from a high strength aluminum alloy. The UltraZip Coupler shall be precision cut and welded 1/2" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel tie plate and will have a multi-stage baked-on powder coat finish. The UltraZip Junction Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel plate and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap shall be fabricated from 3/8" steel and will have multi-stage baked-on powder coat finish. The UltraZip Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel. The UltraZip Deck shall be Play-Tuff coated after fabrication. The UltraZip Deck Legs shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will have a multi-stage baked-on powder coat finish. The Split Collar Half shall be fabricated using 1/4" thick HR steel and will have a multi-stage baked-on powder coat finish. The UltraZip Beam Pin shall be fabricated using AISI 1045 cold drawn steel. The Hanger Pin shall be fabricated using AISI 303 stainless steel. The UltraZip Ramp shall be fabricated using punched, formed, and welded 12 gauge sheet steel and 2.875" O.D. sch. 40 pipe and shall be Play-Tuff coated after fabrication. The Grip Ramp Bracket shall be fabricated using precision cut and welded 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The Grip Ramp Foot shall be fabricated using precision cut 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap Bumper shall be fabricated using PN 579108 D-Shaped, O-Bore Bumper. 1850 - Arc Post Topper The Arc Post Topper R35/R5 shall be fabricated using 3.5" or 5" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. R5 13011 - Half Square Deck Steel Wall R5 The Half Square Deck Steel Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with a welded 1/4" thick steel tab and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1936 - Ring Pull Up The Ring Pull-Up shall be 1-1/2" x 3" tubing designed to attach the complete unit to upright posts and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1214 - Climbing Wall The Chain Mount Bracket shall be laser-cut 1/4" thick steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Climb Chain Hanger shall be laser-cut 3/8" thick plate steel. The Climb Chain Hanger shall have clear zinc plating. The Grip Climb Wall shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Grip Climb Wall Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish and shall be Play-Tuff(TM) coated. The Grip Climb Wall Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 1.315" O.D. 12 gauge steel cross member with welded 3/8" thick steel tab and will be Powder Coated as specified. The Grip Ramp Bracket shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. The Ramp Grips shall be precision die-cast from a high strength aluminum alloy and shall have a thermoplastic coating. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1126 - Center Access Hex Deck The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck Barrier and Handle shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2477 - Spin Max Go-Round The Spin Max Base & Top shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Flange shall be formed using 1/4" thick sheet steel and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Go-Round Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel plates and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs, 3/8" thick steel ring blocks and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin Max Sit Down Rope shall be made from 16mm steel-reinforced rope with machined aluminum end ferrules. The Spin Max Base Spacers & Roto Ferrule Plugs shall be machined from high strength aluminum. The Spin Max Top, Cover Panel & Rope Bridge Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rope Bridge Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1385 - Dual Dino Rider The Dual Dino Rider Body, Seat, Handles, Footrests and Spacers shall be made from high-density 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV-stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Spring Mount Puck shall be precision die-cast from high-strength aluminum alloy and will be Powder Coated as specified. The Bottom Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Top Spring Mount Plate shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. The Spring Rider Bracket shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. NF 5302 - NFuse Slither Climber Extension The Slither Climber Support Mount Bracket shall be punched and formed from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Slither Climber & Roto Plug shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Supports shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting bracket, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing, 1.029" O.D. 14 gauge steel tubing, and 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel clevises, 3/16" thick steel clevises, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. NF-5206 - NFuse Explorer's Arch Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Top Rail & NFuse Molecule Bay - Bottom Rail shall be fabricated using 2.375" O.D. steel tubing with welded 1/4" thick steel clevises and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Side Rail shall be fabricated using 1.900" O.D. steel tubing with welded 1/4" thick steel clevises and 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Extension Frame shall be fabricated using 1-1/2" x 3" x .120" Rectangular TS, welded 1/4" thick steel plates and clevises, 3/16" thick stainless steel clevises and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The NFuse Explorer's Arch Bay - Ladder shall be fabricated using 2.375" O.D., 1.900" O.D. and 1.315" O.D. steel tubing with welded 1/4" thick steel plates and 5/8" HR round bar and will have a multi-stage baked-on powder coat finish. The Round Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The NFuse Explorer's Arch Bay - Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The NFuse Explorer's Arch Bay - Back Rest shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The NFuse Explorer's Arch Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The Roto Panel Net Bracket shall be fabricated using 3/16" thick steel bracket with welded 3/16" thick steel clevis and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5203 - NFuse Tri-Ring Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket, Chain Surface Mount Weldment, & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Tri-Ring Bay - Inner & Outer Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Chain shall be 5/0 galvanized chain. The Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The NFuse Tri-Ring Bay - S-Plate shall be precision cut from 10 gauge stainless steel. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5201 - NFuse Hex Net Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bottom Weldment shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Bracket shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside & Top Outside Weldment shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. 5104 - NFuse Hex Net Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Frame Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" thick stainless steel. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 5103 - NFuse Geo-Hex Wall Frame The NFuse Geo Hex Wall Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel clevises and tabs and will have a multi-stage baked-on powder coat finish. The NFuse Geo-Hex Wall Frame HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks & Lugs shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5102 - NFuse 2-Rung Access Ladder Frame The NFuse 2-Rung Access Ladder Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube, 1.315" O.D. 12 gauge steel tubing and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 18021 - Shade Canopy Square Roof The Roof Canopy Jack Screw shall be fabricated using 2" O.D. 10 gauge steel tube with welded 3/16" thick steel plugs, welded 1" O.D. machined steel retainer stub, 1" O.D. 11 guage steel cable spacer and punched 10 gauge steel retainers and will be Powder Coated as specified. The Roof Canopy Square Rafter Hub shall be fabricated using 2.50" O.D. schedule 40 pipe with welded zinc nut and stainless steel stop and will be Powder Coated as specified. The Roof Canopy Square Rafter shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel plug and will be Powder Coated as specified. The Roof Canopy Support Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to a formed 3/16" thick steel cradle and will be Powder Coated as specified. The Shade Canopy Square shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. The 1/4" Canopy Wire Cable shall be Ø1/4" steel cable with a clear vinyl coating. 12161 - Flex Grip Climber The Flex grip Climber Rail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge handle, 1/4" thick steel tabs and mounting plate and will be powder coated as specified. The Flex Grip Climber Pad shall be constructed of UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. The Ramp Grip shall be one piece and precision die-cast from a high strength aluminum alloy. The Ramp Grip comes in 2-hole and 3-hole styles and is finished with a vinyl coating. 4250 - Rectangular Picnic Table The Table Top & Bench shall be fabricated from punched, formed, and welded 14 gauge sheet steel and shall be Play Tuff(TM) coated after fabrication. The Table Frame Brace shall be fabricated from punched and formed 10 gauge sheet steel and shall have a powder coat finish. The Table Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounts and shall have a powder coat finish. The Frame Support shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1910 - Talk Tube The Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen and 1/4" thick steel tabs and will be Powder Coated as specified. The Steel Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing and 5" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen, 3/16" thick steel reducer/flanges, 5/8" round bar steel, and 1/4" thick steel tabs and will be Powder Coated as Specified. The Talk Tube Cone shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Socket Clamp shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1613 - Tube Panel The Tube Section & R5 Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The R35 Panel, Stiffener, & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tube Slide Leg Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing welded to a 3/16" thick steel plate and 5/8" steel rod and will have a multi-stage baked-on powder coat finish. The Window shall be fabricated using .118 thick clear polycarbonate. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1410 - Loop Traverse The Loop Traverse 90 Deg. Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab and will be Powder Coated as specified. The Loop Traverse 144" R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports, 1/2" thick steel tab, and 1/4" thick steel clevises and will be Powder Coated as specified. The Loop Traverse shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports with 1/4" thick steel clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1328 - Curved Wall The Curved Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails and will be Powder Coated as specified. The Curved Wall with Wheel Mount Plate shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails. A .188" thick mounting plate shall be welded to the vertical rails and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1236 2 - Erector Rock with Hole The Erector Rock with Hole shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1236 1 - Erector Rock Small The Erector Rock Small shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1219 - Deep Rung Arch Climber The Arch Climber Deep Rung shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1220 - Centipede Climber The Centipede Climber shall have a center support constructed of 2.375" O.D. 10 gauge Tube Steel with 1.315" O.D. 12 gauge Tube Steel stepping/gripping loops welded on and will be Powder Coated as specified. 1209 HW - Transfer Station with Half Walls The Decks & Steps shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Powder Coated as specified. The Step Deck Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Transfer Deck Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting bracket and will be Powder Coated as specified. The Transfer Rail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, 1.029" O.D. 14 gauge steel rails, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Leg Top shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Vertical Filler shall be fabricated using punched 1/8" thick aluminum alloy and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1107 - Curved Deck Assembly The Curved Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.