5501 - NFUSE NIMBLE BAY BRIDGE The Socket Clamp Rope Clevis shall be fabricated from 3/16" thick stainless steel. The Angled Net Link Deck Connector & Nfuse Hex Net Bay Brackets shall be fabricated from 1/4" thick steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Nfuse Hex Net Bay Top Inside Weldment shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Ladder shall be fabricated from 2.375" O.D. 11 gauge and 1.315" O.D. 12 gauge steel tubing with welded 3/16" thick stainless steel clevises and machined ferrules and will have a multi-stage baked-on powder coat finish. The Bay Bridge Outside Rail shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick stainless steel clevises and 1/4" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Support Legs shall be fabricated from 1-1/2"x3"x.120" steel tubing with welded 12 gauge, 3/8", and 3/16" thick steel caps, tabs, and clevises and 5/8" O.D. anchors and will have a multi-stage baked-on powder coat finish. The Bay Bridge Support Leg Stiffeners shall be fabricated from 2.375" O.D. 11 gauge steel tubing with welded 1/4", 3/8", and 3/16" thick steel caps, tabs, and clevises and will have a multi-stage baked-on powder coat finish. The Bay Bridge Side Rail shall be fabricated from 2.375" O.D. 11 gauge steel tubing with welded 3/8" and 3/16" thick steel tabs and clevises and machined ferrules and will have a multi-stage baked-on powder coat finish. The Bay Bridge Top Rail shall be fabricated from 3.5" O.D. 11 gauge steel tubing with 3/16" thick stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. The Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Nimble Bay Bridge Net shall be made from 20mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Nfuse Curved Swage R35 Shade Post shall be fabricated from 3.5" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. R5 21263 - Launch Pad Step R5 The Launch Pad Step Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1429 - 90 Deg. Horizontal Ladder The Horizontal Ladder support beams shall be fabricated from 2.375" O.D. 10 gauge tube steel with 1.315" O.D. 12 gauge tube steel rungs uniformly spaced and welded in place and will be Powder Coated as specified. R5 1317 - Triple Twister Entry Panel The Triple Twister Slide Entry Panel and Stiffener shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Head Rail shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to 1/4" Steel tabs and will be Powder Coated as specified. The Sit Down Side Guard shall be fabricated from 1.029" O.D. 14 gauge tube steel welded to 10 gauge mounting tabs and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC-2479 - Mini-Go-Round The Mini-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Mini-Go-Round Deck & Seat shall be fabricated using punched, formed, and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mini-Go-Round Driver Wheel shall be made from high density 1" thick sheet plastic specially formulated for optimum UV stability and color retention. The Mini-Go-Round Frame shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. The Mini-Go-Round Center Post shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3/8" thick and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Mini-Go-Round Bracket Spacer shall be made from precision cut 1/4" thick steel and will be Powder Coated as specified. The Mini-Go-Round Bracket shall be fabricated using welded 3/16" and 3/8" thick steel plates and will be Powder Coated as specified. The Mini-Go-Round Top Rail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC-2476 - Spin Max Tower The Spin Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Tower Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel top plate, 1/4" thick steel bottom plate and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Rope Clevis shall be formed using 3/16" thick stainless steel and will be Powder Coated as specified. PC-2439 - Tri Spring Deck The Tri Spring Deck shall be fabricated using punched and formed 12 gauge sheet steel and will be Play-Tuff ™ coated after fabrication. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will have a multi-stage baked-on powder coat finish. The Event Spring Retainer shall be precision cut and formed from 1/8" thick steel and will have a multi-stage baked on powder coat finish. The Multi-Spring Deck Mounting Plate shall be fabricated using 1/4" thick plate steel and will have a multi-stage baked-on powder coat finish. PC 2425 - Horizontal Log The Horizontal Log Support Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel support bracket and will be Powder Coated as specified. The Log Climber - Horizontal Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 2272 - Boulder Stack The Boulder Stack Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Boulder Stack Bottom Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Geo Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rock Spacer shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Top, Mid & Base Rock shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. 5205 - NFuse Ring Traverse The NFuse Ring Traverse Weldment shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" plates and 3/16" thick steel hangers and will have a multi-stage baked-on powder coat finish. The NFuse Ring Traverse - Top Inside Weldment shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" plates and 3/16" thick steel clevises (for deck mount version) and will have a multi-stage baked-on powder coat finish. The NFuse Ring Traverse - Rubber Pad shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Deck Link Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. 5204 - NFuse Molecule Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment & NFuse Molecule Bay - Bottom/Top Outside Rails shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Inner /Top Nets & Deck Link Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The NFuse Molecule Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors, rotationally molded LDPE blocks, and machined aluminum end ferrules. 5203 - NFuse Tri-Ring Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket, Chain Surface Mount Weldment, & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Tri-Ring Bay - Inner & Outer Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Chain shall be 5/0 galvanized chain. The Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. The NFuse Tri-Ring Bay - S-Plate shall be precision cut from 10 gauge stainless steel. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5104 - NFuse Hex Net Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Frame Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" thick stainless steel. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 5102 - NFuse 2-Rung Access Ladder Frame The NFuse 2-Rung Access Ladder Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube, 1.315" O.D. 12 gauge steel tubing and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1961 S - Stump Step The Stump Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Stump Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Stump Step Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1930 - Chinning Bar The Chinning Bar R5 & R35 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and shall have a powder coat finish. The Chinning Bar R5 Hybrid & RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting brackets and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. 1918 - Banister Glide The Banister Glide shall be fabricated from 1.900" O.D. 11 gauge steel tubing for the rails. The Banister Glide will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1705 - Quarter Turn Slide The Quarter Turn Slide shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Quarter Turn Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 1/4" steel plate and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1312 - Wall With HDPE Seat The Wall W/ HDPE Seat shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel vertical rails and 1/4" thick steel tabs and will be Powder Coated as specified. The Seat shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1290 - Boulder Stack Climber The Boulder Stack Bottom Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Boulder Stack Filler Plate shall be fabricated using punched 10 gauge sheet steel and will be Powder Coated as specified. The Boulder Stack Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Geo Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rock Spacer shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Top, Mid & Base Rock shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1276 - Chain Wave Climber The Chain Wave Climber shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel mounting bracket and 3/8" thick steel tabs and will be Powder Coated as specified. The Chain Wave Climber Net shall be fabricated from lengths of 5/0 chain and shall be Play-Tuff(TM) coated after fabrication. 1240 - Terrace Climber The Terrace Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel rails with welded 1.315" O.D. 12 gauge steel rungs and 3/16" thick steel mounting plate and will be Powder Coated as specified. The Terrace Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 5/8" O.D. steel anchor and will be Powder Coated as specified. 1236 CSM CST - Slotted End Cap The Erector Rock Slotted End Cap shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.