1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R5 18094 4 - Quad Corrugated Gable Roof R5 The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Braces, Roof Sections, Roof Flashing, Ridge Cap & Roof End Plates shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The End Plate, Gable Roof Stiffeners & Sign shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 18031 - Corrugated Hex Roof The Braces, Roof Sections & Ridge Caps shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Steel Hex Roof Cap shall be fabricated using punched, formed and welded 14 gauge sheet steel and will be Powder Coated as specified. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Roof Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5-12891-DD - Center Access Climber Deck to Deck The Center Access Square Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Climber D.to D. R5 shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. R5 1960 - Tree House Bench R5 The Tree House Bench Base and Top R5 shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1936 - Ring Pull Up The Ring Pull-Up shall be 1-1/2" x 3" tubing designed to attach the complete unit to upright posts and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1849 - Tree Root R5 The Tree Root Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. The Tree Root R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1847 - Tree Top Roto R5 The Tree Top Roto R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1830 STL - Steel Telescope on Wall R5 The Steel Telescope shall be fabricated using 5" O.D. 11 gauge steel tubing with welded 3.5" O.D. 11 gauge steel tubing, and 3/16" thick steel flange, front plate, back plate, and reducer and will be Powder Coated as specified. The Steel Telescope Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs, and 1/4" thick steel tabs and 3/16" thick steel mounting plate and will be Powder Coated as specified. The Steel Telescope Curved Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs, 1/4" thick steel tabs, 3/16" thick steel mounting plate and 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Steel Telescope Wall Mount shall be fabricated using 3/16" thick steel mounting plate with welded 1/4" thick steel mounting tabs and will be Powder Coated as specified. The Steel Telescope Caps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Steel Telescope Lenses shall be made from .118" thick polycarbonate. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1707 8 SP - Spiral Tube Slide 96" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1707 6 L - L-Shaped Tube Slide 6 Section 72" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1689 - City Scape Assembly The City Scape Panels & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Castle Tab 30 Degree shall be precision cut and formed from 3/16" thick sheet steel and will be Powder Coated as specified. The Flat Panel bracket shall be precision cut from 3/16" thick sheet steel and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision cut and formed from 3/16" thick sheet steel and will be Powder Coated as specified. The Truck Handle Small shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge sheet steel mounting plates and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1677 - Tree House Panel Assembly The Panels, Spacer, Plug & Counter shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Panel & Spring Rider Bracket shall be precision laser-cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Tree House Access Handle & Sit Down Side Guard shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Tree House Panel Trim & Window Trim shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Roto Panel Lug shall be machined from high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1536 - 180 Degree Crawl-Netix Climbers The Crawl-Netix Flange Stiffeners/Support Arm Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net/Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net Sections shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail Sections shall be fabricated using 1.029" O.D. 14 gauge and 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and steel clevises and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Split Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Bottom Support Arm shall be fabricated using 1.900" O.D. 11 gauge, 2.375" O.D. 11 gauge, and 2.875" O.D. schedule 40 steel tubing with welded 1/4" thick steel plate and clamps and will be Powder Coated as specified. The Crawl-Netix Tube Clamp shall be fabricated using 3/16" thick sheet steel with a welded steel ball bearing and will be Powder Coated as specified. The Ball Joint Socket shall be machined from UHMW plastic. R5 1535 - Crawl-Netix Climber R5 The Crawl-Netix Flange Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Roto Panel Leg shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 3/16" thick bracket, and a 1/4" thick steel plate and will be Powder Coated as specified. The Roto Round Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1525 - Ramp Link R5 The Grip Ramp Brackets shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Ramp Link shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM)coated after fabrication. The Ramp Link Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel vertical rails and 1/4" thick steel tabs and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Toddler Grips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1511 - Curved Bridge The Inner and Outer Walls shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 3"-5/8" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gage tube steel rails, top and bottom and will be Powder Coated as specified. The Curved Bridge shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. R5 1500 STL - Steel Crawl Tube 45" The Steel Crawl Tube shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Crawl Tube Panels shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1325 - Wall Above Telescope The Wall Above Telescope shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5-1292 - Stump Climber R5 The Stump Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Stump Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tree Root Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1242 - Ladder Deck to Deck The Deck to Deck Ladder shall have side supports constructed using 1.315" O.D. 12 gauge tube steel and 1.315" O.D. 12 gauge tube steel rungs evenly spaced and welded to the side supports and will be Powder Coated as specified. R5 1222 - Snake Climber The Snake Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 1/4" thick steel mounting plate and will be Powder Coated as specified. R5 1208 6 FT - 6' Ramp R5 The Ramp R5 6' shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets. The Ramp shall be Play-Tuff(TM) coated after fabrication. The Rail Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. The Rail Set will be powder coated as specified. The Wall Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing. The Wall Set will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy. The Mounting Blocks will be powder coated as specified. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 2918 - Conifer Climber The Tree Root Leg shall be fabricated using 1.029" O.D. steel tubing with welded 10 gauge steel plate and 5/8" round bar and will be Powder Coated as specified. The Roto Tree Climb Handle, Limb Stump, Straight, & Top shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC 2488 - Tidal Wave The Tidal Wave Seat Middle and End shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tidal Wave Frame Sections Middle and Ends Shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff (TM) coated after fabrication. The Tidal Wave Center Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 1/4" HR Sheet Steel Tidal Wave Center Post Base, 10 gauge HR Sheet Steel Tidal Wave Center Leg Gussets, a 10 gauge HR Sheet Steel Torsion Spring Shroud 120 and a 3.5" x .1875" Wall Square Tubing Housing and will be Powder Coated as specified. The Tidal Wave End Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 3.5" x .1875" Wall Square Tubing Housing, a 10 gauge HR Sheet Steel Torsion Spring Shroud 200, 1/8" HR Strip Steel Tidal Wave End Leg Caps and a Steel Tidal Wave End Pivot Axle and will be Powder Coated as specified. The Torsion Spring Mount shall be bent and formed from 1/4" HR Sheet Steel and will be Powder Coated as specified. The Tidal Wave End Pivot Base Weldment shall be made of punched and formed 1/4" HR Sheet Steel and a Steel Tidal Wave Pivot Bearing Sleeve and will be Powder Coated as specified. The Tidal Wave End Post Base Plates shall be precision laser cut from 1/4" HR Sheet Steel. The Tidal Wave End Post Base Plates will be Powder Coated as specified. The Torsion Spring Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2472 - Spin-Max Orbit The Spin-Max Cover Halves, Support Cap & Steps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Spin-Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin-Max Orbit Cross Supports shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" tabs and clevises and will be Powder Coated as specified. The Spin-Max Orbit Main Support Tubes shall be fabricated using 1.5" x 3" 11 gauge rectangular steel tubing with welded 2" x 2" x 1/4" thick square steel tubing and welded 1/4" thick steel clevises, 1/4" thick steel plate, 12 gauge steel caps, and steel plug and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Orbit Support Leg shall be fabricated using 5" schedule 80 pipe with welded 3/8" thick steel mounting plate and gussets and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Spin-Max Orbit Ropes shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Hex Net Rubber Plug Top & Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 1/4" plates and plug, 3/8" thick steel plates, and machined steel spindle and will be Powder Coated as specified. The Spin-Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will Powder Coated as specified. The Spin-Max Base Spacer shall be machined from high strength aluminum. PC 2426 - Alligator Balance Beam The Alligator Balance Beam shall be constructed of UV-stabilized, rotationaly molded, linear, low density polyethylene with an average wall thickness of .250". The Alligator Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. PC 2272 - Boulder Stack The Boulder Stack Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Boulder Stack Bottom Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Geo Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rock Spacer shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Top, Mid & Base Rock shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC-1920 - Spring See-Saw The Post Base shall be fabricated using 5.0" O.D. 7 ga T.S., 1/2" thick sheet steel, and 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Spring See Saw Beam shall be fabricated using 4" X 4" x .120" square tube, 1.900" O.D. 11 gauge steel tube with welded 1/4" thick steel mounting plate, brackets, gussets, 12ga steel cap and 10 gauge steel brackets and will have a multi-stage baked-on powder coat finish. The Pivot Axle shall be fabricated from 11 gauge steel tube and will have a multi-stage baked-on powder coat finish. The See Saw Body Components shall be made from high density 3/4" and 1" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will have a multi-stage baked-on powder coat finish. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will have a multi-stage baked-on powder coat finish. The See Saw Bracket shall be fabricated from 10 gauge steel and will have a multi-stage baked-on powder coat finish. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy. The Pipe End Cap shall be fabricated from 1-3/8" OD black acetel copolymer rod. 5101 - NFuse Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 1975 - Trans-Glide Asembly The Retainer Plate shall be precision cut from 1/4" thick steel and will be Powder Coated as specified. The Spring Rider Bracket shall be precision cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Trans-Glide Base shall be precision cut and welded from 1/4" thick steel with welded 1.900" 11 gauge steel stiffeners and will be Powder Coated as specified. The Trans-Glide Bench Back & Seat shall be punched, formed and welded from 14 gauge sheet steel with 12 gauge steel gussets and end caps and shall be Play-Tuff(TM) coated after fabrication. The Trans-Glide Bench rail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting tabs and will be Powder Coated as specified. The Trans-Glide Bench Skirt shall be punched, formed and welded from 10 gauge sheet steel and will be Powder Coated as specified. The Trans-Glide Bumper shall be 3/8" thick, 3-ply rubber belt. The Trans-Glide Dampener & Torsion Bracket shall be precision cut and formed from 3/8" thick steel and will be Powder Coated as specified. The Trans-Glide Deck & Transition Deck shall be punched formed and welded from 12 gauge sheet steel and shall be Play-Tuff™ coated after fabrication. The Trans-Glide Dampener Plate shall be made from Ultra High Molecular Weight Polyethylene for lasting durability. The Trans-Glide Drive Arm & Drive Plate shall be precision cut from 1/2" thick steel and will be Powder Coated as specified. The Trans-Glide Driveshaft shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded machined steel spindles and 1/4" thick steel mounting plate and will be Powder Coated as specified. The Trans-Glide Driveshaft Bracket shall be fabricated using welded precision cut 1/2" thick steel tabs and will be Powder Coated as specified. The Trans-Glide Handle shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Drive House shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 10 gauge steel gussets and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Trans-Glide Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Torsion Arm shall be fabricated using 3-1/2" square 3/16" thick wall tubing with welded 1/4" thick steel gussets and 1-1/4" square 1/8" thick wall tubing arm and will be Powder Coated as specified. The Trans-Glide Track Wheel shall be machined Nylon 6/6. The Trans-Glide Wheel Hub shall be fabricated using precision cut and formed 3/8" thick steel and machined stainless steel axles. The Trans-Glide Wheel Hub Stiffener shall be punched, formed, and welded from 10 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1961 S - Stump Step The Stump Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Stump Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Stump Step Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1949 - Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing welded to 1/4" reinforcer plates and a 3/8" top plate and will be Powder Coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Stand-N-Spin Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be Powder Coated as specified. The Stand-N-Spin Base & Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. The External Snap Ring shall be zinc and yellow chromate-plated steel and have an internal diameter of 2". 1831 - Telescope Assembly The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Swivel Bracket shall be precision laser-cut and formed from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. The Telescope Lens Large and Small shall be fabricated using .118" thick polycarbonate. The Telescope Disc Spacer Post Mount shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Post Cap shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1705 - Quarter Turn Slide The Quarter Turn Slide shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Quarter Turn Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 1/4" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1613 - Tube Panel The Tube Section & R5 Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The R35 Panel, Stiffener, & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tube Slide Leg Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing welded to a 3/16" thick steel plate and 5/8" steel rod and will have a multi-stage baked-on powder coat finish. The Window shall be fabricated using .118 thick clear polycarbonate. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1506 - Suspension Bridge The Suspension Bridge Guardrail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Wall shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Transition Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Side Plate shall be precision laser cut from 3/16" thick steel plate and will be Powder Coated as specified. The Mounting Blocks shall be two-part precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from high strength aluminum alloy. The Socket Clamps shall be two-part and precision die-cast from high strength aluminum alloy and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1291 - Inclined Log Climber The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with formed 1/4" thick end tab and will be Powder Coated as specified. The Geo-Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Log Climber - Deck Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Deck Bracket shall be fabricated using 1/4" thick steel mounting plate with welded 1/4" thick steel tabs and will be Powder Coated as specified. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1261 - Ebb & Flow Climber The Ebb & Flow Climber Frame, and Platform Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" and 3/16" thick steel clevises and 1.900" steel mount plugs and will be Powder Coated as specified. The Ebb & Flow Anchor Brackets shall be fabricated using 1/4" thick stainless steel and will be Powder Coated as specified. The Ebb & Flow Horizontal Strut shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/16" thick steel clevises and 1.900" steel mount plug pins and will be Powder Coated as specified. The Ebb & Flow Deck Plate shall be fabricated using 1/4" thick steel plating with welded 3/16" thick steel clevises and will be Powder Coated as specified. The Ebb & Flow Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connecters and machined aluminum ferrules. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1248 - Poly Climb Wall The Poly Climb Wall Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge sheet steel cross brackets and will be Powder Coated as specified. The Poly Climb Wall shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Grip Ramp Bracket shall be two part laser-cut and welded from 1/4" thick steel and will be Powder Coated as specified. The Ramp Grip shall be one piece and precision die-cast from a high strength aluminum alloy and comes in 2-hole and 3-hole styles and is finished with a vinyl coating. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1236 3 - Erector Rock Curve The Erector Rock Curved shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1234 DSC - Spiral Step Climber to Post The Spiral Step Climber to Post shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates. The Spiral Step Climber to Post will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1224 - Stacked Loop Climber The Stacked Loop Climber shall have main rails constructed of 1.660" O.D. 11 gauge tube steel with 1.315" O.D. 12 gauge tube steel stepping/gripping loops welded to the main rails and will be Powder Coated as specified. 1219 - Deep Rung Arch Climber The Arch Climber Deep Rung shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1103 - Half Hex Deck 5 Post Assembly The Half Hex Deck 5 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.