RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. RV 1959 - Tri Ring Hub RV The Tri-Ring Hub Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Tri-Ring Hub Rail with Mounts RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails, 1/4" thick stainless steel mounting brackets, and stainless steel pins and will be Powder Coated as specified. The Post Tab Bracket RV shall be fabricated from 1/4" thick stainless steel mounting bracket with welded 3/8" thick steel tab and will be Powder Coated as specified. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250", and .375" thick molded in aluminum mounting plates. R35 1802 - Poly Ribbed Roof The Poly Ribbed Roof shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R35 1707 3 - Tube Slide 3' H The Tube Sections shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The R3.5 Tube Slide Panel and Tube Panel Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. R35-1600 - R3.5 Panel Assembly The R3.5 Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1500 2 S - 2 Section S-Shaped Crawl Tube Tube Sections shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Crawl Tube Panel and Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV- stability and color retention. The Bottom Castings and Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1500 2 I - 2 Section Inclined Crawl Tube Tube Sections shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Crawl Tube Panel and Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Bottom Castings and Mounting Lugs shall be precision die-cast from a high strength aluminum alloy will be Powder Coated as specified. R35 1411 90 - 90 Deg. Loop Traverse The 90° Loop Traverse shall have a center support beam constructed of 2.375" O.D. 10 gauge tube steel welded to 1-1/2" x 3" rectangular steel tubing cross members with clevises punched from 1/4" thick HR steel grade A36. The Loops shall be made from 1.315" O.D. 12 gauge tube steel and uniformly spaced and welded to center support beam and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1405 - S-Shaped Horizontal Ladder The S-Shaped Horizontal Ladder shall be fabricated from 2.375" O.D. 10 gauge tube steel support beams with 1.315" O.D. 12 gauge tube steel rungs uniformly spaced and welded in place and will be Powder Coated as specified. R35 1314 - R3.5 Wall Access The R3.5 Access Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel bracket shall be precision cut and formed from 3/16" thick sheet steel and will be Powder Coated as specified. The Roto Panel Bracket R5 shall be punched and formed from 10 gauge sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R35 1305 - Double Sit Down R3.5 The Double Sit Down and Back Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Double Sit Down Leg shall be fabricated from 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. The Mounting Blocks shall be two-part precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1304 - Sit Down Wall R3.5 The Sit Down Wall and Spacers high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1301 - R3.5 Wall Assembly The R3.5 Wall shall be made from high-density, 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1238 - ROTO Freeform Climber The Roto Freeform Climber shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". Supports shall be made of 2.375" O.D. 10 gauge tube steel with welded deck mount made of 1.315" O.D. tube steel and 1/4" thick HR steel brackets. The Supports will be Powder Coated as specified. R35 1223 - Spiral Climber The Spiral Climber R3.5 shall be fabricated using 1.660"O.D. 11 gauge steel tubing with welded 1.315 O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs, and 1/4" thick steel mounting plate and will be Powder Coated as specified. R35 1222 - Snake Climber The Snake Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 1/4" thick steel mounting plate and will be Powder Coated as specified. R35 1214 6 - Climbing Wall 6' H The Climbing Wall shall be fabricated from punched and formed 12 gauge sheet steel with a punched hole pattern to provide a variety of attachment points for climbing grips. The Climbing Wall shall be finished with a Play-Tuff(TM) coating. Climbing grips shall be one-piece 2-hole and 3-hole precision die-cast from a high strength aluminum alloy. The Grips shall be finished with a Play-Tuff(TM) coating. The Climbing Chain shall be made from 5/0 galvanized steel chain. The Climbing Chain shall be finished with a Play-Tuff(TM) coating. The Grip Climb Wall Leg shall be fabricated from 1.660" O.D. 11 gauge tube steel with a 1.315" O.D. 12 gauge tube steel cross member and a laser cut 1/4" connector plate. The Grip Climb Wall Leg will be Powder Coated as specified. R35 1212 - Vertical Step Climber The Vertical Step Climber R3.5 shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs will be Powder Coated as specified. R35 1109 - Balcony Deck The Balcony Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1100 - Deck Identification NO SPECIFICATIONS R5 12801 - Sunrise Climber R5 The Sunrise Climber R5 shall be fabricated using 1.315" O.D. 12 gauge steel rungs with welded 1.900" O.D. 11 gauge steel frame, 1/4" thick steel mounting plate and clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1807 - Poly Shingled Roof The Poly Shingled Roof shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R5 1803 - Hex Roof The Hex Roof halves shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R5 1707 6 - Tube Slide 6 Section 72" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1429 - 90 Deg. Horizontal Ladder The Horizontal Ladder support beams shall be fabricated from 2.375" O.D. 10 gauge tube steel with 1.315" O.D. 12 gauge tube steel rungs uniformly spaced and welded in place and will be Powder Coated as specified. R5 1428 - Burma Loop Traverse The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R5 1331 2 3 - Wall Panel Options The Roto Panel Options shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Bracket Panel Roto shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. R5 1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1307 - Handle The Handle shall be fabricated from 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1238 - ROTO Freeform Climber The Roto Freeform Climber shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". Supports shall be made of 2.375" O.D. 10 gauge tube steel with welded deck mount made of 1.315" O.D. tube steel and 1/4" thick HR steel brackets. The Supports will be Powder Coated as specified. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC-2920 - Conifer Net Climber The Conifer Net Climber Beam shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge handles, 3/16" thick steel anchors and 3/16" thick steel tabs and will be powder coated as specified. The Conifer Net Climber Net shall be made from 16 mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Net Climber Anchor Plate shall be fabricated using precision 1" steel plate and will be powder coated as specified. The Roto Tree Climb Handle, Limb, Stump, Straight & Top shall be constructed of UV-Stabilized, rotationaly molded, linear, low density polyethylene with an average wall thickness of .250". PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2476 - Spin Max Tower The Spin Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Tower Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel top plate, 1/4" thick steel bottom plate and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Rope Clevis shall be formed using 3/16" thick stainless steel and will be Powder Coated as specified. PC-2454 - Spinner Seat The Spinner Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spinner Seat Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will have a multi-staged baked-on powder coat finish. The Spinner Seat Hub shall be fabricated using a machined stainless steel hub with welded 3/16" thick steel mounting plate and will have a multi-staged baked-on powder coat finish. PC 2285 - Jet Stream Climber The Jet Stream Climber Arches shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will be Powder Coated as specified. The Jet Stream Climber Leg shall be fabricated using O.D. gauge tube steel and will be Powder Coated as specified. Jet Stream Climber Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. Jet Stream Climber Rails shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will be Powder Coated as specified. The Chain shall be 5/0 galvanized chain with Play-Tuff coating. The Geo-Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250" and .375" thick molded in aluminum mounting plates. PC 2181 - Single Post Swings The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC-1920 - Spring See-Saw The Post Base shall be fabricated using 5.0" O.D. 7 ga T.S., 1/2" thick sheet steel, and 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Spring See Saw Beam shall be fabricated using 4" X 4" x .120" square tube, 1.900" O.D. 11 gauge steel tube with welded 1/4" thick steel mounting plate, brackets, gussets, 12ga steel cap and 10 gauge steel brackets and will have a multi-stage baked-on powder coat finish. The Pivot Axle shall be fabricated from 11 gauge steel tube and will have a multi-stage baked-on powder coat finish. The See Saw Body Components shall be made from high density 3/4" and 1" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will have a multi-stage baked-on powder coat finish. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will have a multi-stage baked-on powder coat finish. The See Saw Bracket shall be fabricated from 10 gauge steel and will have a multi-stage baked-on powder coat finish. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy. The Pipe End Cap shall be fabricated from 1-3/8" OD black acetel copolymer rod. PC 1391 - Multi-Spring Speed Boat The Fixed Mount Leg shall be fabricated using 3-1/2" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Multi-Spring Vehicle Deck shall be fabricated using punched, formed and welded 12 gauge sheet steel, reinforcing cross members, gussets, and 1/4" thick steel mounting plates and shall be Play-Tuff(TM) coated after fabrication. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Speed Boat Brackets shall be punched and formed using 10 gauge sheet steel and will be Powder Coated as specified. The Speed Boat Panels & Seats shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-satbility and color retention. The Speed Boat Rails shall be fabricated using 1.029" O.D. 14 gauge steel tubing and will be Powder Coated as specified. The Spindle shall be made from 1" stainless steel. The Spring Inground Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Spring Mount Plate shall be made from 1/4" thick steel plate and will be Powder Coated as specified. The Spring Mount Puck shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spring Rider Bracket & Castle Tabs shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Spring Vehicle Rear Step shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Truck Handle Small Shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated as specified. The Truck Stirrup Step shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting brackets and will be Powder Coated as specified. The Wheel Hub shall be machined from Ø3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1919 - Slither Climber The Slither Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Supports shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting bracket and will be Powder Coated as specified. The Slither Roto Plug shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Support Mount Bracket shall be punched and formed from 3/16" thick sheet steel and will be Powder Coated as specified. 1830 - Telescope On Wall The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Mounting Bracket shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Telescope Disc Spacer Wall and Mounting Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Telescope Lens Small and Large shall be fabricated using .118" thick Polycarbonate. The Telescope Swivel Bracket shall be 3-pieces precision laser-cut and welded together from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1705 - Quarter Turn Slide The Quarter Turn Slide shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Quarter Turn Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 1/4" steel plate and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1328 - Curved Wall The Curved Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails and will be Powder Coated as specified. The Curved Wall with Wheel Mount Plate shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails. A .188" thick mounting plate shall be welded to the vertical rails and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1283 - Matrix Rope Net Wall The Matrix Rope Net Beam RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting brackets, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Matrix Rope Net Beam RH5 & RH3.5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting brackets and split collars, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as pecified. The Matrix Rope Net Beam R5 & R3.5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel split collars, 3/16" thick steel anchors, and 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Matrix Rope Net shall be made from 16mm teel-reinforced rope with high-strength copolymer plastic intersection onnectors and machined aluminum end ferrules. The Post Anchor Bracket RV shall be fabricated using a 1/4" thick steel mounting bracket with welded 3/16" thick steel anchor and will be Powder Coated as specified. The Post Anchor Bracket R5 & R3.5 shall be fabricated using a 1/4" thick steel split collar with welded 3/16" thick steel anchor and will be Powder Coated as specified. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1281 - Arch Twist Climber The Arch Twist Climber shall be 1.315" O.D. 12 gauge steel rungs, spokes and upper rail welded to 1.900" O.D. 11 gauge steel outer hub and lower rail with 1/4" steel clevises for mounting and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1280 - Swoop Rung Climber The Swoop Rung Climber shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick mounting plates and 3/8" thick steel tabs and will be Powder Coated as specified. The Swoop Rung Climber Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and will be Powder Coated as specified. 1278 MNT - Angled Rung Climber to Mount RV The Angled Rung Climber to Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, rungs and stainless steel housing and will be Powder Coated as specified. 1277 MNT - Angled Lunar Climber to Mount RV The Angled Bubble Climber Panel & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Angled Bubble Climber to Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and stainless steel housing and will be Powder Coated as specified. 1249 DDH DGH - Geo-Wave Climber Horizontal The Geo-Wave Climber shall be constructed of UV-stabilized, rotationally molded, linear low density polyethylene with an average double wall thickness of .250". The Geo-Wave Deck Mount Bracket shall be formed from 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 Gauge steel tubing with formed 1/4" thick end tab and will have a multi-stage baked-on powder coating. The Deck Filler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1243 - Disc Pole Climber The Disc Pole Climber Half Disc shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Disc Pole Climber Poles shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. 1236 CSM CST - Slotted End Cap The Erector Rock Slotted End Cap shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". 1236 3 - Erector Rock Curve The Erector Rock Curved shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1221 - Chain Net Climber shall be constructed of 1.315" O.D. 12 gauge steel rungs affixed to 5/0 chain on 12" centers to form a complete chain net unit and will have a Play-Tuff(TM) coating. The Chain Net Foot shall be fabricated of 1/4" thick steel bent 90° with welded on rebar extensions and will be Powder Coated as specified. The Optional Handrails shall be made from 1.315" O.D. tube steel and welded into the appropriate shape and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1218 - Arch Climber The Arch Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1205 - Access Ramp Border Timbers and Connectors The Ramp Wheelchair Halves Black, The Border Timber Connector (Ramp) and The Border Timber 4' L Black shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". 1107 - Curved Deck Assembly The Curved Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.