R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R35 1214 6 - Climbing Wall 6' H The Climbing Wall shall be fabricated from punched and formed 12 gauge sheet steel with a punched hole pattern to provide a variety of attachment points for climbing grips. The Climbing Wall shall be finished with a Play-Tuff(TM) coating. Climbing grips shall be one-piece 2-hole and 3-hole precision die-cast from a high strength aluminum alloy. The Grips shall be finished with a Play-Tuff(TM) coating. The Climbing Chain shall be made from 5/0 galvanized steel chain. The Climbing Chain shall be finished with a Play-Tuff(TM) coating. The Grip Climb Wall Leg shall be fabricated from 1.660" O.D. 11 gauge tube steel with a 1.315" O.D. 12 gauge tube steel cross member and a laser cut 1/4" connector plate. The Grip Climb Wall Leg will be Powder Coated as specified. R5 18094 4 - Quad Corrugated Gable Roof R5 The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Braces, Roof Sections, Roof Flashing, Ridge Cap & Roof End Plates shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The End Plate, Gable Roof Stiffeners & Sign shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 18061 - Corrugated Extended Hex Roof The Braces, Roof Sections & Ridge Caps shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Extended Steel Hex Roof Cap shall be fabricated using punched, formed and welded 14 gauge sheet steel and will be Powder Coated as specified. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated s specified. The Roof Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 18031 - Corrugated Hex Roof The Braces, Roof Sections & Ridge Caps shall be fabricated using punched and formed 14 gauge sheet steel and will be Powder Coated as specified. The Corrugated Roofing shall be fabricated using formed 29 gauge galvanized sheet steel. The Steel Hex Roof Cap shall be fabricated using punched, formed and welded 14 gauge sheet steel and will be Powder Coated as specified. The Post Brackets shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Roof Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 18012 - 2 Post Square Shade Roof The Steel Shade Roof shall be constructed of 14 gauge sheet steel with punched hole pattern welded to a 1.315" O.D. 12 gauge tube steel frame and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1941 ADA - Boogie Board w/ ADA Walls R5 The Boogie Board Body shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Boogie Board Bottom Panel, Top Panel and Wheels shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Boogie Board Handrail shall be constructed of a 1.660" O.D. 11 gauge steel main rail with a 1.315" O.D. 12 gauge secondary rail and a 3/8" thick steel mounting tab will be Powder Coated as specified. The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The ADA Half Walls shall be fabricated of 1.029" O.D. 14 gauge tube steel welded vertically between the 1.315" O.D. 12 gauge tube steel rails with Tabs welded on to the top of the main rail to provide attachment points and will be Powder Coated as specified. R5-1719-1720 - Roller Slide The Slide Spacer shall be fabricated using formed and welded 12 gauge sheet steel and will be Play-Tuffᵀᴹ coated after fabrication. The Slide Roller shall be made from high viscosity polycarbonate. The Roller Slide Axle shall be cut from 5/8" stainless steel rod. The Roller Slide Bed Brace shall be fabricated from 1.660" O.D. 11 gauge steel tubing with welded 3/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Frame shall be fabricated from 1-1/2" x 3" 11 gauge rectangular tubing with riveted 14 gauge sheet steel and 3/16" thick plate steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Leg Tube shall be fabricated from 1.660" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Roller Slide Blocks shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1707 12 SP - R5 Spiral Tube Slide 144" The Crawl Tube Section shall be constructed of UV-stabilized, rotationally molded linear low density polyethylene. All tube sections are single-wall construction with an average wall thickness of .250". The Tube Slide Support shall be fabricated of 2.375" 10 gauge and 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded on as a footing anchor and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 1/4" steel plate for mounting to tube flange and will be Powder Coated as specified. The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded on as a footing anchor and will be Powder Coated as specified. R5 1707 4 C - Curved Tube Slide 4 Section 48" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1536 - 180 Degree Crawl-Netix Climbers The Crawl-Netix Flange Stiffeners/Support Arm Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net/Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net Sections shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail Sections shall be fabricated using 1.029" O.D. 14 gauge and 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and steel clevises and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Split Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Bottom Support Arm shall be fabricated using 1.900" O.D. 11 gauge, 2.375" O.D. 11 gauge, and 2.875" O.D. schedule 40 steel tubing with welded 1/4" thick steel plate and clamps and will be Powder Coated as specified. The Crawl-Netix Tube Clamp shall be fabricated using 3/16" thick sheet steel with a welded steel ball bearing and will be Powder Coated as specified. The Ball Joint Socket shall be machined from UHMW plastic. R5 1535 - Crawl-Netix Climber R5 The Crawl-Netix Flange Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Roto Panel Leg shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 3/16" thick bracket, and a 1/4" thick steel plate and will be Powder Coated as specified. The Roto Round Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1519 - Marsh Bridge The Marsh Bridge Walls shall be fabricated using 1.315" O.D. 12 gauge tube steel main rails with 1.029" O.D. 14 gauge tube steel horizontal rungs and welded on 1/4" steel clevises for mounting to the support posts and will be Powder Coated as specified. The Marsh Bridge shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Marsh Bridge Rubber Inserts shall be made from 3 ply rubber belt. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1511 - Curved Bridge The Inner and Outer Walls shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 3"-5/8" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gage tube steel rails, top and bottom and will be Powder Coated as specified. The Curved Bridge shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. R5 1500 2 I - 2 Section Inclined Crawl Tube Tube Sections and Crawl Tube Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1331 2 3 - Wall Panel Options The Roto Panel Options shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Bracket Panel Roto shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1293 - Net Tower Ladder R5 The Socket Clamp Rope Clevis shall be fabricated using a 1/4" thick stainless steel and will have a multi-stage baked-on powder coat finish. The Net Tower Ladder R5 shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum Rope Anchor Ferrule. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. R5 1242 - Ladder Deck to Deck The Deck to Deck Ladder shall have side supports constructed using 1.315" O.D. 12 gauge tube steel and 1.315" O.D. 12 gauge tube steel rungs evenly spaced and welded to the side supports and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1212 - Vertical Step Climber The Vertical Step Climber R5 shall be fabricated using 12 gauge punched sheet steel. The Vertical Step Climber R5 will be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs will be Powder Coated as specified. R5 1208 8 FT - 8' Ramp R5 The Ramp R5 8' shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuff coated after fabrication. The Rail Set 8' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will be Powder Coated as specified. The Wall Set R5 8' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1208 6 FT - 6' Ramp R5 The Ramp R5 6' shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets. The Ramp shall be Play-Tuff(TM) coated after fabrication. The Rail Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. The Rail Set will be powder coated as specified. The Wall Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing. The Wall Set will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy. The Mounting Blocks will be powder coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1201 - Easy Access Stairs The Easy Access Stairs shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Easy Access Stair Handrails shall be fabricated using 1.315" O.D. 12 gauge tube steel and welded to tabs for mounting to the Stair Rail Brackets and Easy Access Stairs and will be Powder Coated as specified. The Stair Half Walls shall be fabricated using 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel rungs and a stair rail tab welded on the outer rail and will be Powder Coated as specified. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4331 - Urban Elite Bench The Elite Bench Back & Seat shall be fabricated using punched, formed and welded 14 gauge and 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Bench Inground Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and will be Powder Coated as specified. The Bench Surface Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and 3/16" thick steel mounting plates and will be Powder Coated as specified. PC 2985 - Rainbow Twist Climber The Rainbow Twist Climber shall be fabricated using 2.375" O.D. 11 gauge steel rails with welded 1.315" O.D. 12 gauge steel rungs. The Rainbow Twist Climber will be Powder Coated as specified. The Rainbow Twist Climber Leg shall be formed and fabricated using 2.375" O.D. 11 gauge steel tubing with welded 5/8" O.D. steel anchor. The Rainbow Twist Climber Leg will be Powder Coated as specified. PC 2488 - Tidal Wave The Tidal Wave Seat Middle and End shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tidal Wave Frame Sections Middle and Ends Shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff (TM) coated after fabrication. The Tidal Wave Center Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 1/4" HR Sheet Steel Tidal Wave Center Post Base, 10 gauge HR Sheet Steel Tidal Wave Center Leg Gussets, a 10 gauge HR Sheet Steel Torsion Spring Shroud 120 and a 3.5" x .1875" Wall Square Tubing Housing and will be Powder Coated as specified. The Tidal Wave End Leg shall be fabricated from 3" x .25" Wall Square Tubing Leg, a 3.5" x .1875" Wall Square Tubing Housing, a 10 gauge HR Sheet Steel Torsion Spring Shroud 200, 1/8" HR Strip Steel Tidal Wave End Leg Caps and a Steel Tidal Wave End Pivot Axle and will be Powder Coated as specified. The Torsion Spring Mount shall be bent and formed from 1/4" HR Sheet Steel and will be Powder Coated as specified. The Tidal Wave End Pivot Base Weldment shall be made of punched and formed 1/4" HR Sheet Steel and a Steel Tidal Wave Pivot Bearing Sleeve and will be Powder Coated as specified. The Tidal Wave End Post Base Plates shall be precision laser cut from 1/4" HR Sheet Steel. The Tidal Wave End Post Base Plates will be Powder Coated as specified. The Torsion Spring Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2485-C - Neutron Carousel The Neutron Spinner Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Neutron Carousel Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel plates and machined steel spindle and will have a multi-stage baked-on powder coat finish. The Neutron Spinner Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 5" O.D. 1/2" thick steel center housing, 1.900" O.D. 11 gauge steel spokes, and 1/4" thick steel gussets and will have a multi-stage baked-on powder coat finish. The Neutron Spinner Dome Cap shall be precision die-cast from a high-strength aluminum alloy with a Ø7/16" center mounting hole and will have a multi-stage baked-on powder coat finish. The Jumbo Rope Top Brackets shall be fabricated using 3/8" precision cut steel with welded machined ferrules and will have a multi-staged baked-on powder coat finish. The Jumbo Rope Bottom Bracket shall be fabricated using 3/16" precision cut stainless steel with welded machined tapered pins. The Jumbo Rope Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Neutron Carousel Ropes shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Neutron Carousel Jumbo Rope shall be made from 140mm steel-reinforced rope. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2472 - Spin-Max Orbit The Spin-Max Cover Halves, Support Cap & Steps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Spin-Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin-Max Orbit Cross Supports shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" tabs and clevises and will be Powder Coated as specified. The Spin-Max Orbit Main Support Tubes shall be fabricated using 1.5" x 3" 11 gauge rectangular steel tubing with welded 2" x 2" x 1/4" thick square steel tubing and welded 1/4" thick steel clevises, 1/4" thick steel plate, 12 gauge steel caps, and steel plug and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Orbit Support Leg shall be fabricated using 5" schedule 80 pipe with welded 3/8" thick steel mounting plate and gussets and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Spin-Max Orbit Ropes shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Hex Net Rubber Plug Top & Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 1/4" plates and plug, 3/8" thick steel plates, and machined steel spindle and will be Powder Coated as specified. The Spin-Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will Powder Coated as specified. The Spin-Max Base Spacer shall be machined from high strength aluminum. PC 2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1387 - Paulie Pony The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick plate steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high strength aluminum. The Spring Rider Panel Set shall be made from high-density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Paulie Pony Handle shall be 1.029" O.D. 14 gauge steel handle with 10 gauge steel mounting plates and will be Powder Coated as specified. PC 1383 - Toad Single Spring Rider The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high-strength aluminum. The Spring Rider Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 1052 - Beach Buggy The Beach Buggy Bumper & Handles shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Beach Buggy Roll Bar shall be fabricated using 1.029" O.D. 14 gauge steel tubing and will be Powder Coated as specified. The Beach Buggy Back & Side Plates shall be made from punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Beach Buggy Tires shall be made from precision cut 14 gauge sheet steel and will be Powder Coated as specified. The Beach Buggy Shifter Hub shall be made from Ultra High Molecular Weight Polyethylene for lasting durability and minimal rotational resistance. The Beach Buggy Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Beach Buggy Plastic Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Beach Buggy Chassis shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Driver Wheel Hub & 11 Inch Driver Wheel shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Wheel Hub & Drive Shifter shall be machined from high strength aluminum alloy and will be Powder Coated as specified. NF 5301 - NFuse Hex Net Extension The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Extension - Frame Rail shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing with welded 5/8" steel anchor, 1/4" thick steel clevis, and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Frame Rail - Surface Mount shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing with welded 1/4" thick steel anchor plate, 1/4" thick steel clevis, and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Extension - Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum ferrules. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 12461 - Cargo Net Climber The 16-Link Galvanized Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel anchors and will be Powder Coated as specified. The cargo Climber Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. 1974 - Gyro-Pod Spinner The Gyro-Pod Capsule Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" x 1-1/2" flat steel reinforcement plates and stainless steel ball bearing and will be Powder Coated as specified. The Gyro-Capsule Top Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.900" O.D. 11 gauge steel supports, 1/4" thick stainless steel mounting brackets and stainless steel ball bearing and will be Powder Coated as finished. The Gyro-Pod Bearing Hub shall be fabricated using 2-1/4" O.D. machined steel hub with welded 1/4" thick steel plate and will be Powder Coated as specified. The Gyro-Pod Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Gyro-Pod Tread Plate shall be made from punched 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Gyro-Pod Ring Plate shall be made from precision cut 1/4" thick sheet steel and will be Powder Coated as specified. The Gyro-Pod End & Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Gyro-Pod Ring Spacer shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Ball Joint Socket Half shall be made from Ultra High Molecular Weight Polyethylene for lasting durability and minimal rotational resistance. The Split Collar Half shall be made from precision cut and formed 1/4" thick stainless steel and will be Powder Coated as specified. 1961 R4 - Rock Step-Up The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The lily Pad Step-Up Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1932 - Hand Spin Cycler The Hand Spin Cycler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1831 - Telescope Assembly The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Swivel Bracket shall be precision laser-cut and formed from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. The Telescope Lens Large and Small shall be fabricated using .118" thick polycarbonate. The Telescope Disc Spacer Post Mount shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Post Cap shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1807 STL - Steel Pyramid Roof The Steel Pyramid Roof Post Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Pyramid Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1705 - Quarter Turn Slide The Quarter Turn Slide shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Quarter Turn Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 1/4" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1613 - Tube Panel The Tube Section & R5 Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The R35 Panel, Stiffener, & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tube Slide Leg Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing welded to a 3/16" thick steel plate and 5/8" steel rod and will have a multi-stage baked-on powder coat finish. The Window shall be fabricated using .118 thick clear polycarbonate. 1426 270 - 270° Round Loop Traverse The Loop Traverse 90° Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab. and will be Powder Coated as specified. The 270° Round Loop Traverse shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.5" x 3" 11 gauge steel end supports, 1.315" O.D. 11 gauge steel loops, 1/2" thick steel tabs and 1/4" thick steel clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1413 - Track Ride The Track Ride Beam shall be hot-extruded from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Track Ride Mid Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab and will have a multi-stage baked-on powder coat finish. The Track Ride Support shall be fabricated using 2" x 3" x .120" Rec T.S. with welded 1/4" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Track Ride Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and stainless steel housing and will have a multi-stage baked-on powder coat finish. The Track Ride Center Support Bracket shall be fabricated using 1/4" thick sheet steel with welded 1/2" thick steel mounting tab and will have a multi-stage baked-on powder coat finish. The Mounting Blocks, Track Ride End Casting, Brake Casting, & Skate Casting shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Track Ride Handle shall be fabricated using 1.029" O.D.14 gauge galvanized steel tubing and 1" O.D. AISI bar stock and will be dipped in thermoplastic coating. The Track Ride Bumper shall be injection-molded from commercial grade rubber. The Track Ride Spacers shall be made from high density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The Track Ride Skate Wheel shall be machined from high-density urethane. The Track Ride Guide Wheel shall be machined from nylon. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1280 - Swoop Rung Climber The Swoop Rung Climber shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick mounting plates and 3/8" thick steel tabs and will be Powder Coated as specified. The Swoop Rung Climber Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and will be Powder Coated as specified. 1261 - Ebb & Flow Climber The Ebb & Flow Climber Frame, and Platform Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" and 3/16" thick steel clevises and 1.900" steel mount plugs and will be Powder Coated as specified. The Ebb & Flow Anchor Brackets shall be fabricated using 1/4" thick stainless steel and will be Powder Coated as specified. The Ebb & Flow Horizontal Strut shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/16" thick steel clevises and 1.900" steel mount plug pins and will be Powder Coated as specified. The Ebb & Flow Deck Plate shall be fabricated using 1/4" thick steel plating with welded 3/16" thick steel clevises and will be Powder Coated as specified. The Ebb & Flow Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connecters and machined aluminum ferrules. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1249 DDH DGH - Geo-Wave Climber Horizontal The Geo-Wave Climber shall be constructed of UV-stabilized, rotationally molded, linear low density polyethylene with an average double wall thickness of .250". The Geo-Wave Deck Mount Bracket shall be formed from 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 Gauge steel tubing with formed 1/4" thick end tab and will have a multi-stage baked-on powder coating. The Deck Filler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1248 - Poly Climb Wall The Poly Climb Wall Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge sheet steel cross brackets and will be Powder Coated as specified. The Poly Climb Wall shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Grip Ramp Bracket shall be two part laser-cut and welded from 1/4" thick steel and will be Powder Coated as specified. The Ramp Grip shall be one piece and precision die-cast from a high strength aluminum alloy and comes in 2-hole and 3-hole styles and is finished with a vinyl coating. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1232 - Track Climber The Track Climber supports shall be fabricated of 1.660" O.D. 11 gauge steel tubing and will be Powder Coated as specified. The Track Climber Treads shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Optional Track Climber Handrails shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1110 1117 STL - Vertical Deck Filler The Vertical Deck Fillers shall be made from 12 Gauge sheet steel and will be Powder Coated as specified. 1110 1117 ALU - Vertical Deck Filler The Vertical Deck Fillers shall be fabricated from .120" sheet aluminum. The Vertical Deck Fillers will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.