R35 1803 - Hex Roof The Hex Roof Halves shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. The Roof Access Cover and Roof Hex Plug shall be made from high density 1/2" sheet plastic specially formulated for optimum UV stability and color retention. R35-1600 - R3.5 Panel Assembly The R3.5 Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. PC 2620 - Hex Climber Traverse The Hex Climber Traverse shall be fabricated using 2.375" O.D. 10 gauge steel tubing rails with welded 1.315" O.D. 12 gauge steel rungs and 1/2" thick steel mounting tabs and will be Powder Coated as specified. The Hex Climber Traverse Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing rails with welded 1.315" O.D. 12 gauge steel rungs and 1/2" thick steel mounting tabs and will be Powder Coated as specified. PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC-2495 - Merry-Go-Round The Merry-Go-Round Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and will be Powder Coated as specified. The Merry-Go-Round Deck Base shall be fabricated using 2" square .120" thick wall Steel tubing with welded 5" O.D. 7 gauge steel hub, 5" O.D. 1/2" thick wall steel hub mount, and machined steel spindle and will be Powder Coated as specified. The Merry-Go-Round Dividers shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Merry-Go-Round Post Support shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel plate and will be Powder Coated as specified. The Merry-Go-Round Deck Plate shall be fabricated using punched 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Merry-Go-Round Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Merry-Go-Round Skirt shall be fabricated using 14 gauge sheet steel and will be Powder Coated as specified. The Merry-Go-Round shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing Weldment shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC 2436 - Wiggle Beam The Wiggle Beam shall be fabricated using punched, formed and welded 12 gauge sheet steel with reinforcing cross members and gussets and will be Play-Tuff(TM) coated after fabrication. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Spring Mount Puck shall be precision die-cast from high-strength aluminum alloy and will be Powder Coated as specified. The Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Spring Inground Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Fixed Mount Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel mounting plate and will be Powder Coated as specified. PC 2181 - Single Post Swings The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 1809 - Triple Hoop The 9' Post R35 shall be fabricated using 3.5" O.D. 11 gauge steel tubing. The Cap & Plugs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Triple Hoop shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 1501 1502 - Sand Digger The Digger Seat Top & Bottom shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Digger Chassis ADA & w/ Seat shall be made from 2.375" O.D. 10ga steel tubing, 2" schedule 80 pipe, 1" round steel bar, 3/16" thick steel plug and will have a multi-stage baked-on powder coat finish. The Digger Leg shall be made from 1.660" O.D. steel tubing, 1-1/4" round steel bar, 5/8" round steel bar, 1/4" and 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. The Digger Handles shall be made from 1.029" O.D. 14ga steel tubing, 1-3/4" stainless tubing, 3/4" x 3/16" DOM Tubing, 12ga HR sheet steel, 10ga HR sheet steel and will have a multi-stage baked-on powder coat finish. The Digger Link shall be made from 1.029" O.D. 14ga steel tubing, 1-3/8" HR steel bar, 5/8" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Digger Bucket shall be fabricated using high strength aluminum. The Digger Bucket Pivot Shaft shall be fabricated using 1/2" O.D. 303 stainless steel bar. PC 1399 - Multi-Spring Fire Truck The Double Bulkhead Spring Vehicle Deck shall be fabricated using punched, formed and welded 12 gauge sheet steel, reinforcing cross members, gussets, and 1/4" thick steel mounting plates and shall be Play-Tuff(TM) coated after fabrication. The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Fire Truck Panels, Seats & Tire Sets shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Fixed Mount Leg shall be fabricated using 3-1/2" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Spindle shall be made from Ø 1" stainless steel. The Spring Inground Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel top mounting plate and will be Powder Coated as specified. The Spring Mount Plate shall be made from 1/4" thick steel plate and will be Powder Coated as specified. The Spring Mount Puck shall be cast from a high-strength aluminum alloy. The Spring Mount Puck shall have a multi-stage baked-on powder coat finish. The Spring Rider Bracket & Castle Tab shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specifed. The Spring Vehicle Rear Step shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Truck Bus Bumper shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated. The Truck Handle Small shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated as specified. The Truck Stirrup Step shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting brackets and will be Powder Coated as specified. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Wheel Insert shall be precision laser-cut from 14 gauge sheet steel and will be Powder Coated as specified. PC 1387 - Paulie Pony The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick plate steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high strength aluminum. The Spring Rider Panel Set shall be made from high-density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Paulie Pony Handle shall be 1.029" O.D. 14 gauge steel handle with 10 gauge steel mounting plates and will be Powder Coated as specified. PC 1383 - Toad Single Spring Rider The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high-strength aluminum. The Spring Rider Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 1343 - Toddler Tractor Spring Rider The Single Spring Bottom Mount Plate shall be made using 1/4" thick plate steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision laser-cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision laser-cut and formed 1/4" thick sheet steel and will be Powder Coated as specified. The Toddler Toad Spring Weldment shall be fabricated using 5-3/4" O.D. spring with a free height of 14" with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Spring Mount Puck shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spring Rider Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Toddler Spring Rider Foot Rest shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 3/16" thick steel plugs and will be Powder Coated as specified.