1632 - Bugeye Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bugeye Bubble shall be fabricated from 3/16" Clear Polycarbonate. R5-1362 - Steel Push-Out Wall The Steel Push-Out Wall shall be fabricated from 1.029" O.D. 14 gauge tubing and 1.315" O.D. 12 gauge tubing with welded on 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Push-Out Seat Panel, Push-Out Wall Round Event Panel, Pushout Seat & Supports shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bug Eye Bubble shall be constructed of 3/16" Clear Polycarbonate. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5-1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1536 - 180 Degree Crawl-Netix Climbers The Crawl-Netix Flange Stiffeners/Support Arm Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net/Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net Sections shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail Sections shall be fabricated using 1.029" O.D. 14 gauge and 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and steel clevises and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Split Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Bottom Support Arm shall be fabricated using 1.900" O.D. 11 gauge, 2.375" O.D. 11 gauge, and 2.875" O.D. schedule 40 steel tubing with welded 1/4" thick steel plate and clamps and will be Powder Coated as specified. The Crawl-Netix Tube Clamp shall be fabricated using 3/16" thick sheet steel with a welded steel ball bearing and will be Powder Coated as specified. The Ball Joint Socket shall be machined from UHMW plastic. R5 1535 - Crawl-Netix Climber R5 The Crawl-Netix Flange Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Roto Panel Leg shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 3/16" thick bracket, and a 1/4" thick steel plate and will be Powder Coated as specified. The Roto Round Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1212 - Vertical Step Climber The Vertical Step Climber R5 shall be fabricated using 12 gauge punched sheet steel. The Vertical Step Climber R5 will be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1100 - Deck Identification NO SPECIFICATIONS PC 2426 - Alligator Balance Beam The Alligator Balance Beam shall be constructed of UV-stabilized, rotationaly molded, linear, low density polyethylene with an average wall thickness of .250". The Alligator Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 18021 - Shade Canopy Square Roof The Roof Canopy Jack Screw shall be fabricated using 2" O.D. 10 gauge steel tube with welded 3/16" thick steel plugs, welded 1" O.D. machined steel retainer stub, 1" O.D. 11 guage steel cable spacer and punched 10 gauge steel retainers and will be Powder Coated as specified. The Roof Canopy Square Rafter Hub shall be fabricated using 2.50" O.D. schedule 40 pipe with welded zinc nut and stainless steel stop and will be Powder Coated as specified. The Roof Canopy Square Rafter shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel plug and will be Powder Coated as specified. The Roof Canopy Support Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to a formed 3/16" thick steel cradle and will be Powder Coated as specified. The Shade Canopy Square shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. The 1/4" Canopy Wire Cable shall be Ø1/4" steel cable with a clear vinyl coating. 1945 - Orbit Wheel The Orbit Wheel Frame shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge supports, 1/4" stainless steel mounting brackets and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Orbit Wheel Frame R35 and R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 11 gauge supports, 1/4" steel split collars and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Traverse Wheel shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded machined stainless steel hub and will have a multi-stage baked-on powder coat finish. The Wheel Traverse Cap shall be fabricated using precision cut 10 gauge stainless steel. The Split Collar Half hall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. 1840 - Palm Post Top The Palm Tree Leaf shall be made from high density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV-stability and color retention. The Palm Tree Flange shall be fabricated using punched and formed 10 gauge sheet steel and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1501-1502 - Arch Bridge The Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Arch Bridge Rails shall be fabricated using 1.660 O.D. 11 gauge steel tubing, 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with 1/4" HR Steel and 10 gauge HR Steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Arch Bridge Wall and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arch Bridge Wall Stiffener shall be made from 1-1/4" HR flat bar and 3/8" HR steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1110 1117 STL - Vertical Deck Filler The Vertical Deck Fillers shall be made from 12 Gauge sheet steel and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.