1710-SUP - Twister Slide Support Assembly The Sectional Slide Support Bracket #2 shall be fabricated using 3/16"HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support shall be fabricated using Ø1.660 steel tubing, 3/16" HR sheet steel and 5/8"round bar and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Top shall be fabricated using Ø2.000 steel tubing and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Twister Slide Support Bottom shall be fabricated using Ø1.660 steel tubing and 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R35-1600 - R3.5 Panel Assembly The R3.5 Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1428 - Burma Loop Traverse 84 The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R35 1304 - Sit Down Wall R3.5 The Sit Down Wall and Spacers high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1213 - Firepole Climber The Firepole shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 3/16" thick steel mounting plate. The Firepole Climber will be Powder Coated as specified. R35 1100 - Deck Identification NO SPECIFICATIONS R5 18093 - Tree House Shed Roof The Tree House Shed Roof shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1960 - Tree House Bench R5 The Tree House Bench Base and Top R5 shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1849 - Tree Root R5 The Tree Root Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. The Tree Root R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1847 - Tree Top Roto R5 The Tree Top Roto R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1677 - Tree House Panel Assembly The Panels, Spacer, Plug & Counter shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Panel & Spring Rider Bracket shall be precision laser-cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Tree House Access Handle & Sit Down Side Guard shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Tree House Panel Trim & Window Trim shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Roto Panel Lug shall be machined from high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5-1292 - Stump Climber R5 The Stump Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Stump Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tree Root Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2472 - Spin-Max Orbit The Spin-Max Cover Halves, Support Cap & Steps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Spin-Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin-Max Orbit Cross Supports shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" tabs and clevises and will be Powder Coated as specified. The Spin-Max Orbit Main Support Tubes shall be fabricated using 1.5" x 3" 11 gauge rectangular steel tubing with welded 2" x 2" x 1/4" thick square steel tubing and welded 1/4" thick steel clevises, 1/4" thick steel plate, 12 gauge steel caps, and steel plug and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Orbit Support Leg shall be fabricated using 5" schedule 80 pipe with welded 3/8" thick steel mounting plate and gussets and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Platform shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Spin-Max Orbit Ropes shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Hex Net Rubber Plug Top & Bottom shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Spin-Max Orbit Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 1/4" plates and plug, 3/8" thick steel plates, and machined steel spindle and will be Powder Coated as specified. The Spin-Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will Powder Coated as specified. The Spin-Max Base Spacer shall be machined from high strength aluminum. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 1974 - Gyro-Pod Spinner The Gyro-Pod Capsule Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" x 1-1/2" flat steel reinforcement plates and stainless steel ball bearing and will be Powder Coated as specified. The Gyro-Capsule Top Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.900" O.D. 11 gauge steel supports, 1/4" thick stainless steel mounting brackets and stainless steel ball bearing and will be Powder Coated as finished. The Gyro-Pod Bearing Hub shall be fabricated using 2-1/4" O.D. machined steel hub with welded 1/4" thick steel plate and will be Powder Coated as specified. The Gyro-Pod Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Gyro-Pod Tread Plate shall be made from punched 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Gyro-Pod Ring Plate shall be made from precision cut 1/4" thick sheet steel and will be Powder Coated as specified. The Gyro-Pod End & Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Gyro-Pod Ring Spacer shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Ball Joint Socket Half shall be made from Ultra High Molecular Weight Polyethylene for lasting durability and minimal rotational resistance. The Split Collar Half shall be made from precision cut and formed 1/4" thick stainless steel and will be Powder Coated as specified. 1945 - Orbit Wheel The Orbit Wheel Frame shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge supports, 1/4" stainless steel mounting brackets and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Orbit Wheel Frame R35 and R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 11 gauge supports, 1/4" steel split collars and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Traverse Wheel shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded machined stainless steel hub and will have a multi-stage baked-on powder coat finish. The Wheel Traverse Cap shall be fabricated using precision cut 10 gauge stainless steel. The Split Collar Half hall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1832 PST - Roto Stove Pipe Post Mount The Roto Stove Pipe shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1615 - Counter Assembly The Counter Assembly shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. 1521 - Net Link The Net Link shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. The Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel anchors and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1506 - Suspension Bridge The Suspension Bridge Guardrail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Wall shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Transition Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Side Plate shall be precision laser cut from 3/16" thick steel plate and will be Powder Coated as specified. The Mounting Blocks shall be two-part precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from high strength aluminum alloy. The Socket Clamps shall be two-part and precision die-cast from high strength aluminum alloy and will be Powder Coated as specified. 1501 1502 - Arch Bridge The Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Arch Bridge Rails shall be fabricated using 1.660 O.D. 11 gauge steel tubing, 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with 1/4" HR Steel and 10 gauge HR Steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Arch Bridge Wall and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arch Bridge Wall Stiffener shall be made from 1-1/4" HR flat bar and 3/8" HR steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1291 - Inclined Log Climber The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with formed 1/4" thick end tab and will be Powder Coated as specified. The Geo-Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Log Climber - Deck Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Deck Bracket shall be fabricated using 1/4" thick steel mounting plate with welded 1/4" thick steel tabs and will be Powder Coated as specified. 1249 DDH DGH - Geo-Wave Climber Horizontal The Geo-Wave Climber shall be constructed of UV-stabilized, rotationally molded, linear low density polyethylene with an average double wall thickness of .250". The Geo-Wave Deck Mount Bracket shall be formed from 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 Gauge steel tubing with formed 1/4" thick end tab and will have a multi-stage baked-on powder coating. The Deck Filler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1240 - Terrace Climber The Terrace Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel rails with welded 1.315" O.D. 12 gauge steel rungs and 3/16" thick steel mounting plate and will be Powder Coated as specified. The Terrace Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 5/8" O.D. steel anchor and will be Powder Coated as specified. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1221 - Chain Net Climber shall be constructed of 1.315" O.D. 12 gauge steel rungs affixed to 5/0 chain on 12" centers to form a complete chain net unit and will have a Play-Tuff(TM) coating. The Chain Net Foot shall be fabricated of 1/4" thick steel bent 90° with welded on rebar extensions and will be Powder Coated as specified. The Optional Handrails shall be made from 1.315" O.D. tube steel and welded into the appropriate shape and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1216 - Grip Climber The Grip Climber shall be fabricated from punched and formed 12 gauge sheet steel with a punched hole pattern to provide a variety of attachment points for climbing grips and shall be Play-Tuff(TM) coated after fabrication. The Grip Ramp Bracket shall be two-part laser-cut and welded from 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel. The Grip Ramp Foot shall have a multi-stage baked-on powder coat finish. The Climbing grips shall be one-piece 2-hole and 3-hole precision die-cast from a high strength aluminum alloy and will have a Thermal Plastic Coating. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.