1445-SEAT - UltraZip - Standard Seat The Pipe Plug shall be precision cut from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish as specified. The UltraZip Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The UltraZip Seat Rope shall be made from 24mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The UltraZip Seat Ferrule and Swivel Pin shall be machined from stainless steel. 18026 - Shade Canopy Hex The Roof Canopy Jack Screw shall be fabricated using 2"O.D.10ga Tube steel, 1" HR round bar, 10ga stainless steel, 10ga HR sheet steel and AISI 304 stainless steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Support Leg shall be fabricated using 2.5" sch 40 pipe, 2.375"O.D. 10ga galvanized T.S. and 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter Hub shall be fabricated using 2.5" sch 40 pipe, 3/8" 1/2" weld nut and 1/2" hex nut and will have a multi-stage baked-on powder coat finish. The Roof Canopy Hex Rafter shall be fabricated using 2.375"O.D. 10ga galvanized T.S. and 1/2" HR sheet steel and will have a multi-stage baked-on powder coat finish. 1445 - UltraZip The UltraZip End Beam shall be extruded from a high strength aluminum alloy with a welded machined aluminum pin. The UltraZip Straight Beam shall be extruded from a high strength aluminum alloy. The UltraZip Coupler shall be precision cut and welded 1/2" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel tie plate and will have a multi-stage baked-on powder coat finish. The UltraZip Junction Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel plate and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap shall be fabricated from 3/8" steel and will have multi-stage baked-on powder coat finish. The UltraZip Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel. The UltraZip Deck shall be Play-Tuff coated after fabrication. The UltraZip Deck Legs shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will have a multi-stage baked-on powder coat finish. The Split Collar Half shall be fabricated using 1/4" thick HR steel and will have a multi-stage baked-on powder coat finish. The UltraZip Beam Pin shall be fabricated using AISI 1045 cold drawn steel. The Hanger Pin shall be fabricated using AISI 303 stainless steel. The UltraZip Ramp shall be fabricated using punched, formed, and welded 12 gauge sheet steel and 2.875" O.D. sch. 40 pipe and shall be Play-Tuff coated after fabrication. The Grip Ramp Bracket shall be fabricated using precision cut and welded 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The Grip Ramp Foot shall be fabricated using precision cut 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap Bumper shall be fabricated using PN 579108 D-Shaped, O-Bore Bumper. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1707 9 U - U-Shaped Tube Slide 108" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5-1707-3 - Tube Slide 3 Section 36" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5-1536 - 180 Degree Crawl-Netix Climbers The Crawl-Netix Flange Stiffeners/Support Arm Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net/Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net Sections shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail Sections shall be fabricated using 1.029" O.D. 14 gauge and 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and steel clevises and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Split Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Bottom Support Arm shall be fabricated using 1.900" O.D. 11 gauge, 2.375" O.D. 11 gauge, and 2.875" O.D. schedule 40 steel tubing with welded 1/4" thick steel plate and clamps and will be Powder Coated as specified. The Crawl-Netix Tube Clamp shall be fabricated using 3/16" thick sheet steel with a welded steel ball bearing and will be Powder Coated as specified. The Ball Joint Socket shall be machined from UHMW plastic. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5 1126 - Center Access Hex Deck The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck Barrier and Handle shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. NF 5302 - NFuse Slither Climber Extension The Slither Climber Support Mount Bracket shall be punched and formed from 3/16" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Slither Climber & Roto Plug shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Slither Climber Supports shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting bracket, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension shall be fabricated using 1-1/2" x 3" x .120" steel rectangular tubing, 1.029" O.D. 14 gauge steel tubing, and 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel clevises, 3/16" thick steel clevises, 5/8" steel anchor (for in-ground version), and 1/4" thick steel anchor plate (for surface mount version) and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Slither Climber Extension Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. 5204 - NFuse Molecule Bay The Socket Clamp Rope Clevis shall be precision cut and formed using 3/16" stainless steel. The NFuse Hex Net Bay - Bracket & Angled Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Top Inside Weldment & NFuse Molecule Bay - Bottom/Top Outside Rails shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel plates and 3/16" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Bay - Inner /Top Nets & Deck Link Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The NFuse Molecule Bay - Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors, rotationally molded LDPE blocks, and machined aluminum end ferrules. 5104 - NFuse Hex Net Frame The NFuse Frame shall be fabricated using 1-1/2" x 3" Rectangle Tube and 1/4" thick steel Clevises and will have a multi-stage baked-on powder coat finish. The NFuse Hex Net Frame Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Socket Clamp Rope Clevis shall be precision cut and formed from 3/16" thick stainless steel. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 18021 - Shade Canopy Square Roof The Roof Canopy Jack Screw shall be fabricated using 2" O.D. 10 gauge steel tube with welded 3/16" thick steel plugs, welded 1" O.D. machined steel retainer stub, 1" O.D. 11 guage steel cable spacer and punched 10 gauge steel retainers and will be Powder Coated as specified. The Roof Canopy Square Rafter Hub shall be fabricated using 2.50" O.D. schedule 40 pipe with welded zinc nut and stainless steel stop and will be Powder Coated as specified. The Roof Canopy Square Rafter shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel plug and will be Powder Coated as specified. The Roof Canopy Support Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to a formed 3/16" thick steel cradle and will be Powder Coated as specified. The Shade Canopy Square shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. The 1/4" Canopy Wire Cable shall be Ø1/4" steel cable with a clear vinyl coating. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1949 - Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing welded to 1/4" reinforcer plates and a 3/8" top plate and will be Powder Coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Stand-N-Spin Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be Powder Coated as specified. The Stand-N-Spin Base & Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. The External Snap Ring shall be zinc and yellow chromate-plated steel and have an internal diameter of 2". 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1615 - Counter Assembly The Counter Assembly shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1275 - Double Deep Rung Climber The Double Deep Rung Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded with .375" thick steel tabs and 1.315" O.D. 12 gauge steel rungs. The Double Deep Rung Climber will be Powder Coated as specified. The Double Deep Rung Climber Half Wall shall be fabricated from Ø 1.315" 12 gauge steel tubing and a Ø 1.029" 14 gauge steel tube with a .25" steel plate and a .25" steel tab welded on. The Double Deep Rung Climber Half Wall will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.