1298 - Cord Climber CORD CLIMBER TOP BAR: Shall be fabricated using 2.375" OD 10ga T.S., 1/4" HR sheet steel, 3/16" HR sheet steel, 3/8" HR sheet steel and AISI 304 stainless steel and will have a multi-stage baked on powder coat finish. CLIMBING ROPE: Shall be made from 24mm steel-reinforced woven rope with machined aluminum end ferrules. CLIMBING ROPE BALL: Shall be made from GEZOFLEX 0.5-1.5 EPDM rubber. CHAIN: Shall be fabricated from 7mm galvanized steel chain. MOUNTING BLOCKS: Shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1632 - Bugeye Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bugeye Bubble shall be fabricated from 3/16" Clear Polycarbonate. 1602-BBL - Bubble Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bubble Window shall be fabricated from 3/16" Clear Polycarbonate. R5-1535-XTD - X2 Crawl-Netix Transition The Support Plates shall be fabricated from 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The X2 Tower SS Plate (Panel 2) & X2 Tower Tube Extension 17 Degree shall be fabricated from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Crawl Tube Elbows shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The X2 SSS HDPE Trim & R3.5 Tube Panel Stiffener shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Rail Section shall be fabricated from 1.660" O.D. 11 gauge steel tubing, 1.029" O.D. 14 gauge steel tubing, 10 gauge sheet steel, and 3/16" steel clevises and will have a multi-stage baked-on powder coat finish. The Crawl-Netix Net Section shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. 13601-X2 - X2 View Panels The Main Panels shall be fabricated using punched 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Panel Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1349-X2 - X2 TOWER SLIDE SIT DOWN ENTRY The X2 Tower Slide Entry shall be punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff (TM) coated after fabrication. The Slide Tube Extension shall be punched, formed and welded 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Slide Panels shall be punched and formed from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Trim & Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1709-X2 - PORTAL SLIDE SPIRAL X2 - R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1428 - Burma Loop Traverse The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R5-1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 18021 - Shade Canopy Square Roof The Roof Canopy Jack Screw shall be fabricated using 2" O.D. 10 gauge steel tube with welded 3/16" thick steel plugs, welded 1" O.D. machined steel retainer stub, 1" O.D. 11 guage steel cable spacer and punched 10 gauge steel retainers and will be Powder Coated as specified. The Roof Canopy Square Rafter Hub shall be fabricated using 2.50" O.D. schedule 40 pipe with welded zinc nut and stainless steel stop and will be Powder Coated as specified. The Roof Canopy Square Rafter shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel plug and will be Powder Coated as specified. The Roof Canopy Support Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to a formed 3/16" thick steel cradle and will be Powder Coated as specified. The Shade Canopy Square shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. The 1/4" Canopy Wire Cable shall be Ø1/4" steel cable with a clear vinyl coating. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1830 - Telescope On Wall The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Mounting Bracket shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Telescope Disc Spacer Wall and Mounting Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Telescope Lens Small and Large shall be fabricated using .118" thick Polycarbonate. The Telescope Swivel Bracket shall be 3-pieces precision laser-cut and welded together from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1281 - Arch Twist Climber The Arch Twist Climber shall be 1.315" O.D. 12 gauge steel rungs, spokes and upper rail welded to 1.900" O.D. 11 gauge steel outer hub and lower rail with 1/4" steel clevises for mounting and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1243 - Disc Pole Climber The Disc Pole Climber Half Disc shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Disc Pole Climber Poles shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1122 - Double Slide Deck Extension The Double Sit Down Extension Wall shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel guard rails, slide insert, and 1/4" thick steel clevises and will be Powder Coated as specified. The Tri-Deck Extension shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.