R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1600 STL - Steel Panel Assembly R5 The Flat Panel Bracket R5 shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Steel Pane R5 shall be precision laser-cut from 1/4" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1429 - 90 Deg. Horizontal Ladder The Horizontal Ladder support beams shall be fabricated from 2.375" O.D. 10 gauge tube steel with 1.315" O.D. 12 gauge tube steel rungs uniformly spaced and welded in place and will be Powder Coated as specified. R5 1428 - Burma Loop Traverse The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R5 1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1208 6 FT - 6' Ramp R5 The Ramp R5 6' shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets. The Ramp shall be Play-Tuff(TM) coated after fabrication. The Rail Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. The Rail Set will be powder coated as specified. The Wall Set R5 6' shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing. The Wall Set will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy. The Mounting Blocks will be powder coated as specified. R5 1126 - Center Access Hex Deck The Center Access Hex Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Hex Deck Barrier and Handle shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 SPN - Spinner Balcony Deck The Spinner Balcony Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Spinner Balcony Deck will be Play-Tuff(TM) coated after fabrication. The Spinner Balcony Deck Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel welded vertically between the top and bottom 1.315" O.D. 12 Gauge tube steel rails and will be Powder Coated as specified. The Spinner shall be made from 3/4" thick H.D.P.E. plastic with a spindle made from precision cast aluminum alloy. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 2985 - Rainbow Twist Climber The Rainbow Twist Climber shall be fabricated using 2.375" O.D. 11 gauge steel rails with welded 1.315" O.D. 12 gauge steel rungs. The Rainbow Twist Climber will be Powder Coated as specified. The Rainbow Twist Climber Leg shall be formed and fabricated using 2.375" O.D. 11 gauge steel tubing with welded 5/8" O.D. steel anchor. The Rainbow Twist Climber Leg will be Powder Coated as specified. PC-2456(1943) - Spring Lily Pad Assembly The Spring Lily Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250. The Spring Lily Bottom Cover & Top Guide shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Spring Lily Plunger Weldment shall be fabricated using a machined 5/8" steel rod with a welded 1/4" thick steel plate and shall have a powder coat finish. The Spring Lily Plunger Guide shall be machined from UHMW. The Spring Lily Leg shall be fabricated using 1.900" O.D. 11 gauge steel tubing and shall have a powder coat finish." PC 1305 1309 - Sign Roto Welcome Options The Roto Welcome Sign shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sign Post shall be made from 1-1/2" x 3" Rectangular steel tubing and will be Powder Coated as specified. 12461 - Cargo Net Climber The 16-Link Galvanized Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel anchors and will be Powder Coated as specified. The cargo Climber Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. 1963 - Seat on Post The Steel Lily Pad shall be fabricated using 12 gauge punched and formed sheet steel and shall be Play-Tuffâ„¢ coated after fabrication. The Seat on Post R5/R3.5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing and shall have a powder coat finish. The Seat on Post RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets and shall have a powder coat finish. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1807 STL - Steel Pyramid Roof The Steel Pyramid Roof Post Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Pyramid Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1803 STL - Steel Hex Roof The Steel Hex Roof Corner Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Hex Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1261 - Ebb & Flow Climber The Ebb & Flow Climber Frame, and Platform Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/4" and 3/16" thick steel clevises and 1.900" steel mount plugs and will be Powder Coated as specified. The Ebb & Flow Anchor Brackets shall be fabricated using 1/4" thick stainless steel and will be Powder Coated as specified. The Ebb & Flow Horizontal Strut shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/16" thick steel clevises and 1.900" steel mount plug pins and will be Powder Coated as specified. The Ebb & Flow Deck Plate shall be fabricated using 1/4" thick steel plating with welded 3/16" thick steel clevises and will be Powder Coated as specified. The Ebb & Flow Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connecters and machined aluminum ferrules. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1224 - Stacked Loop Climber The Stacked Loop Climber shall have main rails constructed of 1.660" O.D. 11 gauge tube steel with 1.315" O.D. 12 gauge tube steel stepping/gripping loops welded to the main rails and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.