1445 - UltraZip The UltraZip End Beam shall be extruded from a high strength aluminum alloy with a welded machined aluminum pin. The UltraZip Straight Beam shall be extruded from a high strength aluminum alloy. The UltraZip Coupler shall be precision cut and welded 1/2" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel tie plate and will have a multi-stage baked-on powder coat finish. The UltraZip Junction Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support, 3/16" thick steel clevis, 1/4" thick stainless steel mounting brackets and 1/2" thick steel plate and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap shall be fabricated from 3/8" steel and will have multi-stage baked-on powder coat finish. The UltraZip Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel. The UltraZip Deck shall be Play-Tuff coated after fabrication. The UltraZip Deck Legs shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will have a multi-stage baked-on powder coat finish. The Split Collar Half shall be fabricated using 1/4" thick HR steel and will have a multi-stage baked-on powder coat finish. The UltraZip Beam Pin shall be fabricated using AISI 1045 cold drawn steel. The Hanger Pin shall be fabricated using AISI 303 stainless steel. The UltraZip Ramp shall be fabricated using punched, formed, and welded 12 gauge sheet steel and 2.875" O.D. sch. 40 pipe and shall be Play-Tuff coated after fabrication. The Grip Ramp Bracket shall be fabricated using precision cut and welded 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The Grip Ramp Foot shall be fabricated using precision cut 1/4" thick steel and will have a multi-stage baked-on powder coat finish. The UltraZip End Cap Bumper shall be fabricated using PN 579108 D-Shaped, O-Bore Bumper. 1709 - Portal Slide The Slide Sections shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube and Portal Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1/4", 3/16" thick steel caps, and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish as specified. The Twister Slide Supports shall be an assembly with two components. The Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel bracket and 5/8" steel rod and will have a multi-stage baked-on powder coat finish as specified. The Bracket shall be punched and formed from 3/16" thick steel and will have a multi-stage baked-on powder coat finish as specified. The Slide Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will have a multi-stage baked-on powder coat finish as specified. R5-18030 - Orbital Shade The Orbital Shade - Post Connectors shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel brackets and tabs and shall have a powder coat finish. The Orbital Shade - Curved Extensions shall be fabricated using 5" O.D. 11 gauge steel tubing with a welded 1/4" thick steel cap and 3/8" thick steel brackets and shall have a powder coat finish. The Orbital Shade - Outside Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and a welded nut and shall have a powder coat finish. The Orbital Shade - Canopy Support Frames shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel tabs and shall have a powder coat finish. The Orbital Shade Canopy shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel tensioner. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1677 - Tree House Panel Assembly The Panels, Spacer, Plug & Counter shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Panel & Spring Rider Bracket shall be precision laser-cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Tree House Access Handle & Sit Down Side Guard shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Tree House Panel Trim & Window Trim shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Roto Panel Lug shall be machined from high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC 2918 O - Oak Tree Climber The Tree Root Leg shall be fabricated using 1.029" O.D. steel tubing with welded 10 gauge steel plate and 5/8" round bar and will be Powder Coated as specified. The Roto Tree Climb Handle, Limb, Stump, Straight, Top branch, & Top Canopy shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 2918 - Conifer Climber The Tree Root Leg shall be fabricated using 1.029" O.D. steel tubing with welded 10 gauge steel plate and 5/8" round bar and will be Powder Coated as specified. The Roto Tree Climb Handle, Limb Stump, Straight, & Top shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC-2476 - Spin Max Tower The Spin Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Tower Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel top plate, 1/4" thick steel bottom plate and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Rope Clevis shall be formed using 3/16" thick stainless steel and will be Powder Coated as specified. PC 2443 - Tri Spring Fling The Tri Spring Fling Frame shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 11 gauge steel legs and handles, 1.660" O.D. 11 gauge steel supports, 1/4" thick steel tabs and a 1/4" thick sheet steel base and will be Powder Coated as specified. The Tri Spring Fling Frame Metal Handle shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 11 gauge steel legs and handle supports, 1.660" O.D. 11 gauge steel supports, 1.315" O.D. 11 gauge handles, 1/4" thick steel tabs and a 1/4" thick sheet steel base and will be Powder Coated as specified. The Spring Fling Handle and Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Tri Spring Fling Plate shall be made from 1/2" thick plate steel and will be Powder Coated as specified. The Event Spring Retainter shall be made from 1/8" thick sheet steel and will be Powder Coated as specified. PC 2425 - Horizontal Log The Horizontal Log Support Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel support bracket and will be Powder Coated as specified. The Log Climber - Horizontal Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1303 - Welcome Safety Sign The Welcome Safety Sign shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Sign Frame shall be 2.375" O.D. 11 gauge tube steel with welded on laser-cut steel brackets and will be Powder Coated as specified. The Sign Post shall be a 2x2 Sq. tube and will be Powder Coated as specified. 12161 - Flex Grip Climber The Flex grip Climber Rail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge handle, 1/4" thick steel tabs and mounting plate and will be powder coated as specified. The Flex Grip Climber Pad shall be constructed of UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. The Ramp Grip shall be one piece and precision die-cast from a high strength aluminum alloy. The Ramp Grip comes in 2-hole and 3-hole styles and is finished with a vinyl coating. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1830 - Telescope On Wall The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Mounting Bracket shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Telescope Disc Spacer Wall and Mounting Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Telescope Lens Small and Large shall be fabricated using .118" thick Polycarbonate. The Telescope Swivel Bracket shall be 3-pieces precision laser-cut and welded together from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1615 - Counter Assembly The Counter Assembly shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1506 - Suspension Bridge The Suspension Bridge Guardrail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Wall shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel clevises and will be Powder Coated as specified. The Suspension Bridge Transition Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Segment shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Suspension Bridge Side Plate shall be precision laser cut from 3/16" thick steel plate and will be Powder Coated as specified. The Mounting Blocks shall be two-part precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from high strength aluminum alloy. The Socket Clamps shall be two-part and precision die-cast from high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1291 - Inclined Log Climber The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 gauge steel tubing with formed 1/4" thick end tab and will be Powder Coated as specified. The Geo-Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Log Climber - Deck Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Deck Bracket shall be fabricated using 1/4" thick steel mounting plate with welded 1/4" thick steel tabs and will be Powder Coated as specified. 1290 - Boulder Stack Climber The Boulder Stack Bottom Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Boulder Stack Filler Plate shall be fabricated using punched 10 gauge sheet steel and will be Powder Coated as specified. The Boulder Stack Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Geo Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rock Spacer shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Top, Mid & Base Rock shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1248 - Poly Climb Wall The Poly Climb Wall Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge sheet steel cross brackets and will be Powder Coated as specified. The Poly Climb Wall shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Grip Ramp Bracket shall be two part laser-cut and welded from 1/4" thick steel and will be Powder Coated as specified. The Ramp Grip shall be one piece and precision die-cast from a high strength aluminum alloy and comes in 2-hole and 3-hole styles and is finished with a vinyl coating. ER-3001/S-1236-3 - ERECTOR ROCK CURVED The Erector Rock Leg Shall be fabricated using 1.660" O.D. steel tubing with welded 1/4" thick steel mounting plate and will have a multi-stage baked-on powder coat finish. The Erector Rock Post shall be fabricated using 3.5" O.D. steel tubing with welded 1/4" thick steel mounting plate. The Erector Rock Steel Post shall have a multi-stage baked-on powder coat finish. The Erector Rock Wall & Caps shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Wall Grip shall be two-part, and precision diecast from a high strength aluminum alloy. The Wall Grips will be Play-Tuff™ coated after fabrication. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1224 - Stacked Loop Climber The Stacked Loop Climber shall have main rails constructed of 1.660" O.D. 11 gauge tube steel with 1.315" O.D. 12 gauge tube steel stepping/gripping loops welded to the main rails and will be Powder Coated as specified. 1221 - Chain Net Climber shall be constructed of 1.315" O.D. 12 gauge steel rungs affixed to 5/0 chain on 12" centers to form a complete chain net unit and will have a Play-Tuff(TM) coating. The Chain Net Foot shall be fabricated of 1/4" thick steel bent 90° with welded on rebar extensions and will be Powder Coated as specified. The Optional Handrails shall be made from 1.315" O.D. tube steel and welded into the appropriate shape and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1218 - Arch Climber The Arch Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 HW - Transfer Station with Half Walls The Decks & Steps shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Powder Coated as specified. The Step Deck Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Transfer Deck Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting bracket and will be Powder Coated as specified. The Transfer Rail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, 1.029" O.D. 14 gauge steel rails, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Leg Top shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Vertical Filler shall be fabricated using punched 1/8" thick aluminum alloy and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1103 - Half Hex Deck 5 Post Assembly The Half Hex Deck 5 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.