R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1222 - Snake Climber The Snake Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 1/4" thick steel mounting plate and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 1387 - Paulie Pony The Single Spring Bottom Mount Plate shall be made using 1/4" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be made from precision cut and formed 3/16" thick plate steel and will be Powder Coated as specified. The Single Spring Top Mount Plate shall be made from precision cut and formed 3/16" thick sheet steel and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision cut and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Anti-Rotation Spacer shall be machined from high strength aluminum. The Spring Rider Panel Set shall be made from high-density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Paulie Pony Handle shall be 1.029" O.D. 14 gauge steel handle with 10 gauge steel mounting plates and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1639 - Clubhouse Assembly The Clubhouse Panels and Trim shall be made from high density 3/4" thick hot extruded sheet plastic specially formulated for optimum UV stability and color retention. The Clubhouse Table Support shall be fabricated using 1.660" O.D. steel tubing welded to a 1/4" thick pipe plug with threaded insert and will be Powder Coated as specified. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs and Socket Clamps shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1218 - Arch Climber The Arch Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1216 - Grip Climber The Grip Climber shall be fabricated from punched and formed 12 gauge sheet steel with a punched hole pattern to provide a variety of attachment points for climbing grips and shall be Play-Tuff(TM) coated after fabrication. The Grip Ramp Bracket shall be two-part laser-cut and welded from 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel. The Grip Ramp Foot shall have a multi-stage baked-on powder coat finish. The Climbing grips shall be one-piece 2-hole and 3-hole precision die-cast from a high strength aluminum alloy and will have a Thermal Plastic Coating. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.