1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. RV 21263 - Launch Pad Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 21000 - Revolution Post Top Cap The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified. RV 16101 - Round Roto Panel RV The Roto Panel Arm RV shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Roto Panel Leg RV shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Round Roto Panel RV shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1968 - Warp Rung Wall RV The Warp Rung Wall RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Warp Rung Wall 1 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, and 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Warp Rung Mall 2 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and stainless steel housings and will be Powder Coated as specified. RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. RV 1955 - Astro Hub RV The Astro Hub Bottom Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets and 3/8" thick steel tabs and will be Powder Coated as specified. The Astro Hub Top Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets and 3/8" thick steel tabs and will be Powder Coated as specified. The Astro Hub Top Rail With Mounts RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets, 3/8" thick steel tabs, and stainless steel pins and will be Powder Coated as specified. The Tri-Steel Net Climber Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 3/8" thick steel tabs and will be Powder Coated as specified. RV 1917 - Glide-N-Twist The Glide-N-Twist Ladder RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.315" O.D. 12 gauge steel handle and rungs with welded 1/4" thick steel mounting brackets and 3/8" thick steel tabs. The Glide-N-Twist Ladder RV will be Powder Coated as specified. The Wave Glider Rail shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 3/8" thick steel tab. The Wave Glider Rail will be Powder Coated as specified. RV 1431 - V-Wing Bar Traverse RV The V-Wing Bar Traverse RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The V-Wing Bar Traverse 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The V-Wing Bar Traverse 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and stainless steel housings and will be Powder Coated as specified. RV 1287 - Angled Wave Rung Climber RV The Angled Wave Rung Climber RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.315" O.D. 12 gauge steel handles and rungs with welded 1/4" thick steel mounting bracket. The Angled Wave Rung Climber RV will be Powder Coated as specified. RV 1286 - Arched Lunar Climber RV The Arched Wall Climber Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arched Panel Climber Frame RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.660" O.D. 11 gauge steel support rails with welded 1/4" thick steel tabs mounting brackets. The Arched Panel Climber Frame RV will be Powder Coated as specified. RV 1279 - Angled Puzzle Climber RV The Angled Puzzle Climber RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.315" O.D. 12 gauge steel handles and rungs with welded 1/4" thick steel mounting bracket and will be Powder Coated as specified. RV 1278 - Angled Rung Climber RV The Angled Rung Climber RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.315" O.D. 12 gauge steel handles and rung with welded 1/4" thick steel mounting bracket. The Angled Rung Climber RV will be Powder Coated as specified. RH-21004 - Single Arm Event Hanger Hybrid The Event Hanger RH shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel clevis and stainless steel pin and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1807 - Poly Shingled Roof The Poly Shingled Roof shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R5 1803 - Hex Roof The Hex Roof halves shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Roof Support Casting shall be precision die-cast from a high strength aluminum alloy. The Roof Support Casting will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1428 - Burma Loop Traverse The Burma Loop Traverse shall be fabricated from 2.375" O.D. 10 gauge tube steel welded to mounting plates with 1.315" O.D. 12 gauge tube steel for the Loops. The Burma Loop Traverse will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1229 - Cross Loop Climber The Cross Loop Climber shall be constructed of 1.660" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1705 - Quarter Turn Slide The Quarter Turn Slide shall be manufactured from UV-stabilized LLDPE (linear low- density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Quarter Turn Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 1/4" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1289 - Cliffhanger Climber The Cliffhanger Climber shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/2" thick steel tabs and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel handle and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails, 1/4" thick steel mounting clevises, 1/4" thick steel tabs, and 1/2" thick steel tab and will have a multi-stage baked-on powder coat finish. The Promenade Deck shall be fabricated using punched, formed, and welded 12 gauge sheet. The Promenade Deck shall be Play-Tuff(TM) coated after fabrication. The Socket Clamps & Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1275 - Double Deep Rung Climber The Double Deep Rung Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded with .375" thick steel tabs and 1.315" O.D. 12 gauge steel rungs. The Double Deep Rung Climber will be Powder Coated as specified. The Double Deep Rung Climber Half Wall shall be fabricated from Ø 1.315" 12 gauge steel tubing and a Ø 1.029" 14 gauge steel tube with a .25" steel plate and a .25" steel tab welded on. The Double Deep Rung Climber Half Wall will be Powder Coated as specified. 1243 - Disc Pole Climber The Disc Pole Climber Half Disc shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Disc Pole Climber Poles shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. 1220 - Centipede Climber The Centipede Climber shall have a center support constructed of 2.375" O.D. 10 gauge Tube Steel with 1.315" O.D. 12 gauge Tube Steel stepping/gripping loops welded on and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.