R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1100 - Deck Identification NO SPECIFICATIONS PC 2410 - Balance Beam Snake The Balance Beam Top Rail shall be fabricated from 3" x 1-1/2" rectangular steel tubing with carriage bolts surface welded six places. The Balance Beam Top Rail shall be Play- Tuff(TM) coated after fabrication. The Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel with 3/16" steel mounting flanges. The Legs will be Powder Coated as specified. 1975 - Trans-Glide Asembly The Retainer Plate shall be precision cut from 1/4" thick steel and will be Powder Coated as specified. The Spring Rider Bracket shall be precision cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Trans-Glide Base shall be precision cut and welded from 1/4" thick steel with welded 1.900" 11 gauge steel stiffeners and will be Powder Coated as specified. The Trans-Glide Bench Back & Seat shall be punched, formed and welded from 14 gauge sheet steel with 12 gauge steel gussets and end caps and shall be Play-Tuff(TM) coated after fabrication. The Trans-Glide Bench rail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting tabs and will be Powder Coated as specified. The Trans-Glide Bench Skirt shall be punched, formed and welded from 10 gauge sheet steel and will be Powder Coated as specified. The Trans-Glide Bumper shall be 3/8" thick, 3-ply rubber belt. The Trans-Glide Dampener & Torsion Bracket shall be precision cut and formed from 3/8" thick steel and will be Powder Coated as specified. The Trans-Glide Deck & Transition Deck shall be punched formed and welded from 12 gauge sheet steel and shall be Play-Tuff™ coated after fabrication. The Trans-Glide Dampener Plate shall be made from Ultra High Molecular Weight Polyethylene for lasting durability. The Trans-Glide Drive Arm & Drive Plate shall be precision cut from 1/2" thick steel and will be Powder Coated as specified. The Trans-Glide Driveshaft shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded machined steel spindles and 1/4" thick steel mounting plate and will be Powder Coated as specified. The Trans-Glide Driveshaft Bracket shall be fabricated using welded precision cut 1/2" thick steel tabs and will be Powder Coated as specified. The Trans-Glide Handle shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Drive House shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 10 gauge steel gussets and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Trans-Glide Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Torsion Arm shall be fabricated using 3-1/2" square 3/16" thick wall tubing with welded 1/4" thick steel gussets and 1-1/4" square 1/8" thick wall tubing arm and will be Powder Coated as specified. The Trans-Glide Track Wheel shall be machined Nylon 6/6. The Trans-Glide Wheel Hub shall be fabricated using precision cut and formed 3/8" thick steel and machined stainless steel axles. The Trans-Glide Wheel Hub Stiffener shall be punched, formed, and welded from 10 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1701 3 - 36" Single Slide The 36" Single Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1218 - Arch Climber The Arch Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1103 - Half Hex Deck 5 Post Assembly The Half Hex Deck 5 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.