RV 1961 - Tri-Pad The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate. The Step Pad Leg will be Powder Coated as specified. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5-1925 - Hex Net Hub R5 The Hex Net Hub Rubber shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. The Hex Net Hub Rubber Plug Top and Bottom shall be machined from high strength aluminum alloy. The Hex Net Hub Nets shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end Ferrules. The Hex Net Hub Top Rail shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel anchors and 1/4" thick steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Hex Net Rubber Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps and Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. The Socket Clamp Clevis shall be fabricated using 3/16" thick stainless steel. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1525 - Ramp Link R5 The Grip Ramp Brackets shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Ramp Link shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM)coated after fabrication. The Ramp Link Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel vertical rails and 1/4" thick steel tabs and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Toddler Grips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1331 2 3 - Wall Panel Options The Roto Panel Options shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Bracket Panel Roto shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. R5 1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 STL - Double Steel Slide Sit Down Bar The Double Steel Slide Sit Down Bar shall be fabricated of 1.315" O.D. 12 gage steel tubing welded horizontally and vertically to produce an entrapment-free Sit-Down Bar and will be Powder Coated as specified. R5 1304 - Sit Down Wall The Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131510 - Playshare Swing Assembly The Playshare Support Beam shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/16" thick steel clevises and tabs and shall have a powder coat finish. The Playshare Seat Hanger Cap shall be precision cut from 14 gauge sheet steel and shall have a powder coat finish. The Playshare Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Playshare Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Playshare Swing Chain shall be 7mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Hanger and Swing Shaft shall be machined from stainless steel. The Panel Icon shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2474 - Enclosed Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel braces and 3/8" thick steel mounting plate and will be powder coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be powder coated as specified. The Enclosed Stand-N-Spin Frame shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 14 gauge steel flanges, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be powder coated as specified. The Enclosed Stand-N-Spin Panels & Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. PC-2457 - Bucket Spinner The Bucket Spinner shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bucket Spinner Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will be Powder Coated as specified. The Spinner Seat Hub shall be fabricated using a machined stainless steel hub with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1905 - Thunder Dome The Thunder Dome Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 3/16" thick stainless steel anchors and steel frame plates and will be Powder Coated as specified. The Thunder Dome Insert Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 3/16" thick stainless steel anchors, steel frame plates, and mounting flange and will be Powder Coated as specified. The Thunder Dome Ladder shall be made from 16 mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end ferrules. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing. The Thunder Dome Leg shall have a multi-stage baked-on powder coat finish. the Thunder Dome Platform frame shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 12 gauge flange and 3/16" thick stainless steel anchors and will be Powder Coated as specified. The Thunder Dome Platform Tread, Peek Insert & Thunder Dome Cap Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV Stability and color retention. The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Dome Pad shall be constructed of UV-stabilized flexible rubber compound with slash proof, reinforced metal inserts. PC 1395 - Dual Airplane The Dual Airplane Body, Seat, Handles, Footrests and Spacers shall be made from high- density 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV-stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall fabricated using 1/8" thick plate steel and will be Powder Coated as specified. The Bottom Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Top Spring Mount Plate shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. The Spring Rider Bracket shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. PC 1380 - Dual Motorcycle The Dual Motorcycle Body, Seat, Handles, Footrests and Spacers shall be made from high-density 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be precision die-cast and formed from 1/8" thick sheet steel and will be Powder Coated as specified. The Bottom Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Top Spring Mount Plate shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. The Spring Rider Bracket shall be fabricated using 3/16" thick plate steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1521 - Net Link The Net Link shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum end clevises. The Net Link Deck Connector shall be fabricated using 1/4" sheet steel with welded 3/16" thick steel anchors and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1234 DSC - Spiral Step Climber to Post The Spiral Step Climber to Post shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates. The Spiral Step Climber to Post will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified. 1220 - Centipede Climber The Centipede Climber shall have a center support constructed of 2.375" O.D. 10 gauge Tube Steel with 1.315" O.D. 12 gauge Tube Steel stepping/gripping loops welded on and will be Powder Coated as specified. 1218 - Arch Climber The Arch Climber shall be fabricated from 1.660" O.D. 11 gauge steel tubing outer rails welded to 1/4" thick steel plates and 1.315" O.D. 12 gauge steel tubing rungs and will be Powder Coated as specified. 1209 HW - Transfer Station with Half Walls The Decks & Steps shall be fabricated using punched, formed, and welded 12 gauge sheet steel and will be Powder Coated as specified. The Step Deck Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Transfer Deck Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting bracket and will be Powder Coated as specified. The Transfer Rail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.660" O.D. 11 gauge steel support, 1.029" O.D. 14 gauge steel rails, and 1/4" thick steel mounting tab and will be Powder Coated as specified. The Transfer Leg Top shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Vertical Filler shall be fabricated using punched 1/8" thick aluminum alloy and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1110 1117 ALU - Vertical Deck Filler The Vertical Deck Fillers shall be fabricated from .120" sheet aluminum. The Vertical Deck Fillers will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.