PC-1906 - Thunder Wedge The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Wedge Step shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Thunder Wedge Net Frame, Thunder Wedge Window & Insert Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick sheet steel and ASAI 304 stainless steel anchors and will have a multi-stage baked-on powder coat finish. The Thunder Wedge Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Thunder Wedge Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing, 3/16" sheet steel and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Cargo Net Surface Mount Bracket shall be fabricated using 1/4" sheet steel plate with a 3/16" stainless steel clevis and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. 1411-X2 - Zigzag Loop Traverse The Loop Traverse 90 deg. 1 End shall be fabricated using 2.375 dia. O.D. 10ga. tube steel, 1.315 dia. O.D. 12ga. tube steel, 1.5" x 3" 11ga. rectangular steel and 1/2" and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Loop Traverse 90 deg. Support shall be fabricated using 1.990 dia. O.D. 11ga. tube steel, 5/8" dia. round bar and 1/2" and 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. The Traverse Middle Support shall be fabricated using 1.990 dia. O.D. 11ga. tube steel, 5/8" dia. round bar and 1/2" and 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 18093 - Tree House Shed Roof The Tree House Shed Roof shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 16461 - Ship Assembly The Anchor Inserts shall be precision cut from 14 gauge stainless steel. The Driver Wheel Casting Spindle shall machined from 1" stainless steel. The Panel Cannon shall be fabricated using 5" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plates and will be Powder Coated as specified. The Dock Panels,Ship Panels & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Ship Jib Frame shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge stand offs, 10 gauge steel end plate, 3/16" thick steel pipe plugs and 3/8" thick steel tabs and will be Powder Coated as specified. The Ship Wheelhouse Bracket shall be precision cut and formed from 3/16" thick sheet steel and will be Powder Coated as specified. The Spring Rider Bracket shall be precision cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Square Corner Bracket shall be precision cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Treasure Chest Top & Side Plates shall be precision cut and from 14 gauge sheet steel and will be Powder Coated as specified. The Twister Sit Down Side Guard shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated as specified. The Vertical Rock Climber Handle shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Dome Post Cap R3.5 shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Mounting Lug shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. R5-12891-DD - Center Access Climber Deck to Deck The Center Access Square Deck R5 shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Center Access Climber D.to D. R5 shall be fabricated using Ø 1.660" 11 gauge steel tubing with welded Ø 1.315" 12 gauge steel rungs and Ø 1.029" 14 gauge steel rails and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1836 - Ship Crow's Nest R5 The Rope Mount Collar R5 shall be fabricated using 1/4" thick steel mounting plate and welded split collar half and will be Powder Coated as specified. The Ship's Crow's Nest Frame R5 shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 14 gauge steel mounting plates, 1/4" thick steel tabs, 3/16" thick steel anchors and split collar half and will be Powder Coated as specified. The Ship's Crow's Nest Cable shall be made from 16 mm steel-reinforced rope with machined aluminum end ferrules. The Ship's Crow's Nest Support R5 shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel tab and split collar half and will be Powder Coated as specified. The Ship's Crow's Nest Trim shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. R5 1676 SAIL - Ship Sail R5 The Viking Ship Sail Frame shall be fabricated using 1.660" O.D. 14 gauge steel tubing with welded 1.029" O.D. 11 gauge steel rails, 10 gauge sheet steel tabs and 1/4" thick steel collar bracket and split collar halves and will be Powder Coated as specified. The Viking Ship Sail shall be fabricated using punched 14 gauge sheet steel and will be Powder Coated as specified. The Split Collar Half R5 shall be precision cut and formed 1/4" thick steel and will be Powder Coated as specified. R5 1676 - Viking Ship Panel Assembly The Viking Panels, Trim, Shields, and Guards shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Viking Ship Sail Frame shall be fabricated of 1.660" O.D. 11 gauge steel tubing with welded 10 gauge sheet steel tabs and reinforced split Collar halves. The Viking Sail Frame will be Powder Coated as specified. The Viking Ship Sail shall be fabricated using 14 gauge punched sheet steel. The Viking Ship Sail will be Powder Coated as specified. The Sit Down Handle Single shall be fabricated of 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates. The Sit Down Panel Handle Single will be Powder Coated as specified. The Brackets and Tabs shall be precision laser cut using 3/16" thick sheet steel. The Brackets and Tabs will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel. The Split Collar Half will be Powder Coated as specified. The Mounting Lug and Inserts shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs and Inserts will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1238 - ROTO Freeform Climber The Roto Freeform Climber shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". Supports shall be made of 2.375" O.D. 10 gauge tube steel with welded deck mount made of 1.315" O.D. tube steel and 1/4" thick HR steel brackets. The Supports will be Powder Coated as specified. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1201 - Easy Access Stairs The Easy Access Stairs shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Easy Access Stair Handrails shall be fabricated using 1.315" O.D. 12 gauge tube steel and welded to tabs for mounting to the Stair Rail Brackets and Easy Access Stairs and will be Powder Coated as specified. The Stair Half Walls shall be fabricated using 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel rungs and a stair rail tab welded on the outer rail and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS R5 1000 - Medallion on Post Assembly The Medallion shall be made from high density 3/4" sheet plastic specially formulated for optimum UV- Stability and color retention. The R5 Medallion Bracket shall be fabricated using punched and formed 12 gauge sheet steel and will be Powder Coated as specified. PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC 4220 S - Square Picnic Table The Bench and Table Top shall be 14 gauge sheet steel punched and formed into the desired shape. The Bench and Table Top shall be Play-Tuff(TM) coated after fabrication. The Square Table Frame Leg shall be 1.660" O.D. 11 gauge tube steel bent into shape with welded 10 gauge end brackets. The Square Table Brace shall be fabricated of 10 gauge sheet steel. The Square Table Brace shall be Play-Tuff(TM) coated after fabrication. The Square Table Frame will be Powder Coated as specified. PC-2496 - Inclusive Merry-Go-Round The Merry-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Merry-Go-Round Handle & Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Merry-Go-Round Deck, Bottom Cover, & Shroud shall be fabricated using punched and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication.The Merry-Go-Round Top Cover, Spacers, & Bottom Cover shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Merry-Go-Round Bracket shall be fabricated using welded 3/8" thick steel plates and will be Powder Coated as specified.The Merry-Go-Round Top Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and welded 3/8" thick steel ring blocks and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2476 - Spin Max Tower The Spin Max Base shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Tower Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel top plate, 1/4" thick steel bottom plate and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs and 3/8" thick steel ring blocks and will be Powder Coated as specified. The Rope Clevis shall be formed using 3/16" thick stainless steel and will be Powder Coated as specified. PC 2474 - Enclosed Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel braces and 3/8" thick steel mounting plate and will be powder coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be powder coated as specified. The Enclosed Stand-N-Spin Frame shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 14 gauge steel flanges, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be powder coated as specified. The Enclosed Stand-N-Spin Panels & Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. PC-2457 - Bucket Spinner The Bucket Spinner shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bucket Spinner Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will be Powder Coated as specified. The Spinner Seat Hub shall be fabricated using a machined stainless steel hub with welded 3/16" thick steel mounting plate and will be Powder Coated as specified. PC 2425 - Horizontal Log The Horizontal Log Support Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 3/16" thick steel support bracket and will be Powder Coated as specified. The Log Climber - Horizontal Mount shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 2181 - Single Post Swings The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1924 - Quad Teeter Totter The Seesaw Handle Bar Cap, Spacers, Oval End Cap and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Seesaw Seat shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Quad Teeter Totter Frame shall be fabricated using 3.5" O.D. 11 gauge steel frame, 2.375" O.D.11 gauge steel stand off, 1.900" O.D. 11 gauge steel posts and 1.315" O.D 12 gauge steel rests with welded 1/4" thick steel base, gussets, tabs and 10 gauge steel brackets and will be Powder Coated as specified. The Quad Teeter Totter Plate shall be precision laser cut from 3/8" thick steel and will be Powder Coated as specified. The Oval End Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will be Powder Coated as specified. 12461 - Cargo Net Climber The 16-Link Galvanized Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Angled Net Link Deck Connector shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel anchors and will be Powder Coated as specified. The cargo Climber Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. 1961 S - Stump Step The Stump Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Stump Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Stump Step Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1945 - Orbit Wheel The Orbit Wheel Frame shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge supports, 1/4" stainless steel mounting brackets and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Orbit Wheel Frame R35 and R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 11 gauge supports, 1/4" steel split collars and machined stainless steel spindle and will have a multi-stage baked-on powder coat finish. The Traverse Wheel shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded machined stainless steel hub and will have a multi-stage baked-on powder coat finish. The Wheel Traverse Cap shall be fabricated using precision cut 10 gauge stainless steel. The Split Collar Half hall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. 1910 - Talk Tube The Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen and 1/4" thick steel tabs and will be Powder Coated as specified. The Steel Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing and 5" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen, 3/16" thick steel reducer/flanges, 5/8" round bar steel, and 1/4" thick steel tabs and will be Powder Coated as Specified. The Talk Tube Cone shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Socket Clamp shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 1835 - Ship Mast Booms The Ship Boom Long Sail Panels shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Ship's Boom Weldment shall be fabricated from 1.660" O.D. 11 gauge tube steel with a split collar half welded to the end and will be Powder Coated as specified. The Transfer Leg Top Castings and Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1820 - Flag on Post Assembly The Flag shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. 1812 - Driver Wheel to Post The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Wheel Hub shall be machined from 3-3/4" Dia. high strength aluminum alloy and will be Powder Coated as specified. The Steering Wheel to Post Bracket shall be precision laser cut from 1/4" thick rolled sheet steel with welded 1.660" 11 gauge steel tubing and 1" Dia. machined stainless steel spindle and will be Powder Coated as specified. The Split Collar Half shall be precision laser cut from 1/4" thick rolled sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1701 3 - 36" Single Slide The 36" Single Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1243 - Disc Pole Climber The Disc Pole Climber Half Disc shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Disc Pole Climber Poles shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. 1232 - Track Climber The Track Climber supports shall be fabricated of 1.660" O.D. 11 gauge steel tubing and will be Powder Coated as specified. The Track Climber Treads shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Optional Track Climber Handrails shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.