R5-1719-1720 - Roller Slide The Slide Spacer shall be fabricated using formed and welded 12 gauge sheet steel and will be Play-Tuffᵀᴹ coated after fabrication. The Slide Roller shall be made from high viscosity polycarbonate. The Roller Slide Axle shall be cut from 5/8" stainless steel rod. The Roller Slide Bed Brace shall be fabricated from 1.660" O.D. 11 gauge steel tubing with welded 3/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Frame shall be fabricated from 1-1/2" x 3" 11 gauge rectangular tubing with riveted 14 gauge sheet steel and 3/16" thick plate steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Leg Tube shall be fabricated from 1.660" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Roller Slide Blocks shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1104 - 5 Post 90" Deck R5 Assembly The 5 Post Deck 90" R5 shall be fabricated using punched, formed and welded 12 gauge sheet steel. The 5 Post Deck 90" R5 shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS 1961 R4 - Rock Step-Up The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The lily Pad Step-Up Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1843 1845 - Freeform Post Topper The Freeform Post Topper shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1406 - Horizontal Ladder The Horizontal Ladder shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and extensions and will be Powder Coated as specified. 1312 - Wall With HDPE Seat The Wall W/ HDPE Seat shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel vertical rails and 1/4" thick steel tabs and will be Powder Coated as specified. The Seat shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1249 DDH DGH - Geo-Wave Climber Horizontal The Geo-Wave Climber shall be constructed of UV-stabilized, rotationally molded, linear low density polyethylene with an average double wall thickness of .250". The Geo-Wave Deck Mount Bracket shall be formed from 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Geo-Wave Climber Leg shall be fabricated using 1.029" O.D. 14 Gauge steel tubing with formed 1/4" thick end tab and will have a multi-stage baked-on powder coating. The Deck Filler shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1122 - Double Slide Deck Extension The Double Sit Down Extension Wall shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel guard rails, slide insert, and 1/4" thick steel clevises and will be Powder Coated as specified. The Tri-Deck Extension shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.