PC-1906 - Thunder Wedge The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Wedge Step shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Thunder Wedge Net Frame, Thunder Wedge Window & Insert Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, 3/16" thick sheet steel and ASAI 304 stainless steel anchors and will have a multi-stage baked-on powder coat finish. The Thunder Wedge Net shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Thunder Wedge Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing, 3/16" sheet steel and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Cargo Net Surface Mount Bracket shall be fabricated using 1/4" sheet steel plate with a 3/16" stainless steel clevis and will have a multi-stage baked-on powder coat finish. The Chain shall be fabricated from 5/0 galvanized steel chain with silver shield finish. 1981 - Sensory Wall The Sensory Wall Leg shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 5/8" O.D. steel anchor and will have a multi-stage baked-on powder coat finish. The Sensory Wall Leg - Surface Mount shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Sensory Ramp Inserts shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Sensory Wall shall be fabricated using 1.029" O.D. 14 gauge and 1.315" O.D. 12 gauge steel tubing with welded 12 gauge and 1/4" thick steel tabs and flanges and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-CLR - Small Color Wheel The Small Color Wheel Front and Back Panels, Inner and Outer Hubs, and Color Chips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-HYP - Small Hypno Station Panel The Small Hypno Station Axle, Holder, Handle, & Rotator shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-TTT - Small Tic-Tac-Toe Panel The Small Tic-Tac-Toe Panel, Small Tic-Tac-Toe Trim, & Tic-Tac-Toe Piece shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1631 - Pin Ball Panel The Pinball Panel Mounting Ring, Rotator, Clamping Rings, & Deflectors shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Pinball Panel Window shall be made from .118 Polycarbonate sheet plastic. 1612 - Alphabet Maze Panel The Alphabet Maze Panel Round shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. RV 21263 - Launch Pad Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 21004 - Single Arm Event Hanger The Event Hanger shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.900" O.D. 11 gauge support rail, 1/4" thick stainless steel mounting brackets and welded stainless steel pin and/or house and will be Powder Coated as specified. The Event Hanger Caps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. RV 21000 - Revolution Post Top Cap The Revolution Post Top Cap sall be precision die-cast from a high-strength aluminum alloy. The Revolution Post Top Cap will be Powder Coated as specified. RV 12591 - Sectional Lunar Climber RV The Post Offset Tab Bracket shall be fabricated using 1/4" steel mounting bracket with welded 3/8" thick steel tab and will be Powder Coated as specified. The Sectional Lunar Climber Panel, Center & Outside Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1968 - Warp Rung Wall RV The Warp Rung Wall RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Warp Rung Wall 1 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs, and 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Warp Rung Mall 2 Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and stainless steel housings and will be Powder Coated as specified. RV 1959 - Tri Ring Hub RV The Tri-Ring Hub Rail RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Tri-Ring Hub Rail with Mounts RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge hand rails, 1/4" thick stainless steel mounting brackets, and stainless steel pins and will be Powder Coated as specified. The Post Tab Bracket RV shall be fabricated from 1/4" thick stainless steel mounting bracket with welded 3/8" thick steel tab and will be Powder Coated as specified. The Tri-Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250", and .375" thick molded in aluminum mounting plates. RV 1435 - Arch Loop Traverse RV The Arch Loop Traverse RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Arch Loop Traverse 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Arch Loop Traverse 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel loops and stainless steel housings and will be Powder Coated as specified. RV 1431 - V-Wing Bar Traverse RV The V-Wing Bar Traverse RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The V-Wing Bar Traverse 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The V-Wing Bar Traverse 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and stainless steel housings and will be Powder Coated as specified. RV 1419 - Tri-Pad Traverse RV The Disc Traverse Beam RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs and 1/4" thick stainless steel mounting brackets and will be Powder Coated as specified. The Disc Traverse beam 1 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs, 1/4" thick stainless steel mounting bracket and stainless steel housing and will be Powder Coated as specified. The Disc Traverse Beam 2 Mount RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 3/8" thick steel tabs and stainless steel housings and will be Powder Coated as specified. The Disc Traverse Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish. The Tri-Pad Traverse Station shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 3/8" thick steel tabs and will be Powder Coated as specified. The Tri-Pad Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. the Tri-Pad with Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Traverse U-Joint shall be stainless steel to resist rust and corrosion. RV 1404 - Access Ladder RV The Access Ladder RV shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, rungs,and 1/4" thick steel mounting bracket nad will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1317 - Triple Twister Entry Panel The Triple Twister Slide Entry Panel and Stiffener shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Head Rail shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to 1/4" Steel tabs and will be Powder Coated as specified. The Sit Down Side Guard shall be fabricated from 1.029" O.D. 14 gauge tube steel welded to 10 gauge mounting tabs and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2181 - Single Post Swings The 8' Single Post Swing Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The 10' Single Post Swing Post shall be fabricated using 5" O.D. 7 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Tree Top Post shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Single Post Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing with welded 3/16" thick steel hangers and will be Powder Coated as specified. The Single Post Swing Casting shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Post Cap shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 1809 - Triple Hoop The 9' Post R35 shall be fabricated using 3.5" O.D. 11 gauge steel tubing. The Cap & Plugs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Triple Hoop shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". 18016 - Steel Gable Shade Roof The Steel Gable Shade Roof shall be 14 gauge sheet steel welded to 1.315" O.D. 12 gauge steel frame and will be Powder Coated as specified. 1963 - Seat on Post The Steel Lily Pad shall be fabricated using 12 gauge punched and formed sheet steel and shall be Play-Tuffâ„¢ coated after fabrication. The Seat on Post R5/R3.5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing and shall have a powder coat finish. The Seat on Post RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets and shall have a powder coat finish. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1930 - Chinning Bar The Chinning Bar R5 & R35 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and shall have a powder coat finish. The Chinning Bar R5 Hybrid & RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting brackets and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. 1803 STL - Steel Hex Roof The Steel Hex Roof Corner Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Hex Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1501 1502 - Arch Bridge The Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Arch Bridge Rails shall be fabricated using 1.660 O.D. 11 gauge steel tubing, 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with 1/4" HR Steel and 10 gauge HR Steel mounting brackets and will have a multi-stage baked-on powder coat finish. The Arch Bridge Wall and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arch Bridge Wall Stiffener shall be made from 1-1/4" HR flat bar and 3/8" HR steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1287 MNT - Angled Wave Rung Climber to Mount RV The Angled Wave Rung Climber to Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles, rungs and stainless steel housing and will be Powder Coated as specified. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.