1701 - Poly Slide 36" 36" SINGLE SLIDE: Shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". SINGLE SLIDE LEG: Shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 10 gauge steel plate and will have a multi-stage baked-on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 11021 - Spiral Deck The 8" Rise Filler 8" shall be fabricated from punched 5052 sheet aluminum and will have a multi-stage baked-on powder coat finish. The Spiral Deck shall be fabricated using punched and formed 12 gauge sheet steel and will be Play-Tuff ™coated after fabrication. The Spiral Deck Half Wall R5 shall be fabricated from 1.315" O.D. 12 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Spiral Deck Wall shall be fabricated from 1.315" O.D. 12 gauge steel tubing, 1.029" O.D. 14 gauge steel tubing, and 1/4" sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks & Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1685-RND - Mosaic Panel Round The Mosaic Panel Round and Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mosaic Blocks shall be made from injection molded plastic. The Activity Panel Tube shall be fabricated from 0.924" O.D. galvanized steel tubing. 1690-CLR - Small Color Wheel The Small Color Wheel Front and Back Panels, Inner and Outer Hubs, and Color Chips shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-ORCL - Small Oracle Panel The Small Oracle Panel, Arrow, Inner & Outer Hubs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-HYP - Small Hypno Station Panel The Small Hypno Station Axle, Holder, Handle, & Rotator shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-BBL - Small Bubble Panel The Small Bubble Panel Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bubble Panel shall be made from polycarbonate. 1690-BELL - Small Bell & Hammer Panel The Small Bell and Hammer Panel & Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bell shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-TTT - Small Tic-Tac-Toe Panel The Small Tic-Tac-Toe Panel, Small Tic-Tac-Toe Trim, & Tic-Tac-Toe Piece shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1690-3ROW - Small 3-in-a-Row Panel The Panel, Slider, & Stop shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1631 - Pin Ball Panel The Pinball Panel Mounting Ring, Rotator, Clamping Rings, & Deflectors shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Pinball Panel Window shall be made from .118 Polycarbonate sheet plastic. 1609 - Mirror Panel The Round Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mirror shall be fabricated from 16 gauge AISI 304 stainless steel sheet. 1630 - Hour Glass Panel The Pin Ball Panel Mounting Ring, Hour Glass Rotator, & Pin Ball Clamping Rings shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Hourglass Window shall be made from .118 thick polycarbonate sheet plastic. 1605 - Clock Panel The Clock Panel, Large & Small Hand Panels shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1612 - Alphabet Maze Panel The Alphabet Maze Panel Round shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1936 - Ring Pull Up The Ring Pull-Up shall be 1-1/2" x 3" tubing designed to attach the complete unit to upright posts and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1653 - Panel Door Tall ROTO The Panel Door Tall Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 RADA - ADA Steps Half Wall The ADA Steps Half Wall shall be fabricated from 1.029" O.D. 14 gauge tube steel welded between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 - Slide Sit Down Hood The Slide Sit Down Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down Hood guard Single shall be constructed of 1.315" O.D. 12 gauge and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1230 - Clover Climber The Clover Climber shall be constructed of 1.900" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate. The Clover Climber will be Powder Coated as specified. R5 1223 - Spiral Climber The Spiral Climber R5 shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel coil, 1.029" O.D. 14 gauge steel stand-offs and 3/16" thick steel mounting tab and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 131410 - Inclusive Swing Seat Assembly Inclusive Swing Seat & Harness shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Pivot Cap, Pivot Spacer, Latch Cap, Latch Housing, Latch Handle, Latch, Latch Spacer, Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC-2454 - Spinner Seat The Spinner Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spinner Seat Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing welded to 3/16" thick steel mounting plate and machined stainless steel spindle and will have a multi-staged baked-on powder coat finish. The Spinner Seat Hub shall be fabricated using a machined stainless steel hub with welded 3/16" thick steel mounting plate and will have a multi-staged baked-on powder coat finish. PC 2410 - Balance Beam Snake The Balance Beam Top Rail shall be fabricated from 3" x 1-1/2" rectangular steel tubing with carriage bolts surface welded six places. The Balance Beam Top Rail shall be Play- Tuff(TM) coated after fabrication. The Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel with 3/16" steel mounting flanges. The Legs will be Powder Coated as specified. PC-2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2120 - Arch Swing Assembly R5 The Swing Arch & Swing Beam shall be fabricated using 5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. PC 2015 - Disc Swing The Disc Swing Arch shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3.5" O.D. X 2.75" I.D. steel Couplers and will be Powder Coated as specified. The Disc Swing Beam shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 2.375" O.D. 10 gauge cross members and 1/2" thick steel plates and will be Powder Coated as specified. The Disc Swing Leg shall be fabricated using 3.5" O.D. 11 gauge steel and will be Powder Coated as specified. The Disc Swing Seat shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Swing Seat Bumper shall be constructed of rotationally molded vinyl with an average wall thickness of .250". The Disc Swing Swivel Plate & Swivel Plate Spacer shall be precision cut from 3/8" thick stainless steel. The Disc Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Arch Swing Casting & Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Roto Ferrule Plug shall be machined from high strength aluminum. The Roto Ferrule Chain Tab, Swing Shaft & Disc Swing Hanger shall be machined from stainless steel. PC 1397 - Multi-Spring School Bus The Double Bulkhead Spring Vehicle Deck shall be fabricated using punched, formed and welded 12 gauge sheet steel, reinforcing cross members, gussets, and 1/4" thick steel mounting plates and shall be Play-Tuff(TM) coated after fabrication. The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and and will be Powder Coated as specified. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The School Bus Panels, Seats & Tire Sets shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Spindle shall be made from Ø 1" stainless steel. The Spring Inground Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel top mounting plate and will be Powder Coated as specified. The Spring Mount Plate shall be made from 1/4" thick steel plate and will be Powder Coated as specified. The Spring Mount Punk shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spring Rider Bracket & Castle Tab shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Spring Vehicle Rear Step shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Truck Bus Bumper shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated as specified. The Truck Handle Small shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 10 gauge steel mounting tabs and will be Powder Coated as specified. The Truck Stirrup Step shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 3/16" thick steel mounting brackets and will be Powder Coated as specified. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Wheel Insert shall be precision laser-cut from 14 gauge sheet steel and will be Powder Coated as specified. 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1910 - Talk Tube The Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen and 1/4" thick steel tabs and will be Powder Coated as specified. The Steel Talk Tube shall be fabricated using 1.900" O.D. 11 gauge steel tubing and 5" O.D. 11 gauge steel tubing with a welded 14 gauge thick steel screen, 3/16" thick steel reducer/flanges, 5/8" round bar steel, and 1/4" thick steel tabs and will be Powder Coated as Specified. The Talk Tube Cone shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Socket Clamp shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Inserts shall be precision die-cast from a high-strength aluminum alloy. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1708 - Tube Supports The Straight and Double Tube Support shall be fabricated of 1/4" plate steel with 1.660" O.D. 11 gauge tube steel welded to the base and will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from 1.900" O.D. 11 gauge tube steel with a welded on 1.315" O.D. 11 gauge bent tube steel and will be Powder Coated as specified. The Tube Support Bracket shall be fabricated from 1/4" plate steel with a welded on 1.660" O.D. 11 gauge tube steel and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1629 - Accessible Panel Assembly The Chime Set shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Mosaic Block shall be injection molded using a high durability plastic for optimum thermal and UV stability. The Mosaic Block Axel shall be cut from 0.75" O.D. 18 gauge steel tubing and will be Powder Coated as specified. The Panels, Retainers and Sliders shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1615 - Counter Assembly The Counter Assembly shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Store Panel Counter Bracket shall be precision laser cut and formed from 3/16" sheet steel and will be Powder Coated as specified. 1613 - Tube Panel The Tube Section & R5 Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The R35 Panel, Stiffener, & Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tube Slide Leg Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing welded to a 3/16" thick steel plate and 5/8" steel rod and will have a multi-stage baked-on powder coat finish. The Window shall be fabricated using .118 thick clear polycarbonate. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1509 - Burma Bridge The Burma Bridge shall be fabricated from 12 gauge punched and formed sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Burma Bridge Wall shall be fabricated of 1.315" O.D. 12 gauge tube steel with welded 1.029" O.D. 14 gauge steel rungs and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1328 - Curved Wall The Curved Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails and will be Powder Coated as specified. The Curved Wall with Wheel Mount Plate shall be fabricated from 1.315" O.D. 12 gauge tube steel with 1.029" O.D. 14 gauge welded vertical rails. A .188" thick mounting plate shall be welded to the vertical rails and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1237 - Vertical Rock Climber The Vertical Rock Climber shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1232 - Track Climber The Track Climber supports shall be fabricated of 1.660" O.D. 11 gauge steel tubing and will be Powder Coated as specified. The Track Climber Treads shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Optional Track Climber Handrails shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified. 1107 - Curved Deck Assembly The Curved Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.