R35 1707 9 U - U-Shaped Tube Slide 108" H The Tube Sections shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The R3.5 Tube Slide Panel and Tube Panel Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R35-1600 - R3.5 Panel Assembly The R3.5 Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1508 - Inclined Loop Link The Inclined Loop Link shall have 1.990" O.D. 12 gauge tube steel side supports and 1.315" O.D. 12 gauge tube steel loops. Loops are evenly spaced and welded to the side supports. Tabs are welded on to the end of each rail to provide attachment points. The Inclined Loop Link will be Powder Coated as specified. R35 1500 2 - 2 Section Crawl Tube Tube Sections shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Crawl Tube Panel and Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Bottom Castings and Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R35 1304 - Sit Down Wall R3.5 The Sit Down Wall and Spacers high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1301 - R3.5 Wall Assembly The R3.5 Wall shall be made from high-density, 3/4" thick, hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Panel Bracket shall be precision cut from 3/16" HR sheet steel and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Mounting Lug shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35-1201 - R3.5 Stair Assembly The Easy Access Stairs shall be fabricated using punched, formed and welded 12 gauge sheet steel with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Easy Access Stair Hand Rails shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded to mounting tabs and will be Powder Coated as specified. The R3.5 Panel Bracket shall be precision cut and formed 3/16" thick steel and will be Powder Coated as specified. The R3.5 Stair Half Walls shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The R3.5 Stair Rail Bracket shall be precision cut and formed 1/4" thick steel and will be Powder Coated as specified. R35 1109 - Balcony Deck The Balcony Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R35 1100 - Deck Identification NO SPECIFICATIONS R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. 18016 - Steel Gable Shade Roof The Steel Gable Shade Roof shall be 14 gauge sheet steel welded to 1.315" O.D. 12 gauge steel frame and will be Powder Coated as specified. 1949 - Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing welded to 1/4" reinforcer plates and a 3/8" top plate and will be Powder Coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Stand-N-Spin Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be Powder Coated as specified. The Stand-N-Spin Base & Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. The External Snap Ring shall be zinc and yellow chromate-plated steel and have an internal diameter of 2". 1918 - Banister Glide The Banister Glide shall be fabricated from 1.900" O.D. 11 gauge steel tubing for the rails. The Banister Glide will be Powder Coated as specified. 1830 - Telescope On Wall The Telescope shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Telescope Mounting Bracket shall be precision laser-cut and formed from 3/16" sheet steel and will be Powder Coated as specified. The Telescope Disc Spacer Wall and Mounting Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Telescope Lens Small and Large shall be fabricated using .118" thick Polycarbonate. The Telescope Swivel Bracket shall be 3-pieces precision laser-cut and welded together from 3/16" thick H.R. sheet steel and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1704 - Poly Wave Slide The Poly Wave Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1514 - Inclined Arch Bridge The Inclined Arch Bridge shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Inclined Arch Wall shall be fabricated using 1.315" O.D. steel tubing with welded 1.029" O.D. vertical rails and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.