PC-2497 - Celebration Spinner CELEBRATION SPINNER BENCH TOP & BENCH ACCENT: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. CELEBRATION SPINNER BENCH RAIL : Shall be fabricated using 1.660" OD 11ga. tube steel,1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi-stage baked on powder coat finish. CELEBRATION SPINNER RAIL: Shall be fabricated using 1.660" OD 11ga. tube steel,1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi-stage baked on powder coat finish. CELEBRATION SPINNER HANDLE: Shall be fabricated using 1.315" OD 12ga. tube steel with 1/4" sheet steel and will have a multi- stage baked on powder coat finish. CELEBRATION SPINNER UPRIGHT BEAM: Shall be fabricated using 1.5"X3"X.120 rect. tube steel with 1/4" and 12ga. sheet steel and will have a multi-stage baked on powder coat finish. HARDWARE: Shall be stainless steel, zinc/nickel plated or galvanized as required to resist rust and corrosion. 1851/PC-1450 - Butterfly Wings The Butterfly Wings shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Butterfly Inserts shall be made from 0.220" sheet PMMA. The Butterfly Wing Covers shall be made from 3/16" HR sheet steel and welded studs and will have a multi-stage baked-on powder coat finish. The Butterfly Split Collars & Split Collar Halves shall be made from 1/4" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Castle Tab 90 Degree shall be made from 3/16" HR sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps & Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 12401 - Thunder Climber The Thunder Dome Wall shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Thunder Dome Frames shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 3/16" thick steel frame plates and will have a multi-stage baked-on powder coat finish. The Thunder Climber Side shall be fabricated using 2.375" O.D. 11 gauge steel tubing, 3/16" thick sheet steel clevis plate and 1/4" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Thunder Climber Deck Link shall be fabricated from 1.660" O.D. 11 gauge steel tubing and 1.315" O.D. 12 gauge steel tubing with a 3/16" thick sheet steel bracket and stainless steel clevises and will have a multi-stage baked-on powder coat finish. The Thunder Dome Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Thunder Climber Leg - Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with a 1/4" sheet steel plate and will have a multi-stage baked-on powder coat finish. The Cargo Net Surface Mount Bracket shall be fabricated using 1/4" sheet steel plate with a 3/16" stainless steel clevis and will have a multi-stage baked-on powder coat finish. The Nets shall be made from 16mm steel-reinforced rope with high-strength copolymer plastic intersection connectors and machined aluminum end ferrules. The Chain shall be fabricated from 7mm galvanized steel chain. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1981 - Sensory Wall The Sensory Wall Leg shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 5/8" O.D. steel anchor and will have a multi-stage baked-on powder coat finish. The Sensory Wall Leg - Surface Mount shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel plate and will have a multi-stage baked-on powder coat finish. The Sensory Ramp Inserts shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Sensory Wall shall be fabricated using 1.029" O.D. 14 gauge and 1.315" O.D. 12 gauge steel tubing with welded 12 gauge and 1/4" thick steel tabs and flanges and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-RMKR - Small Rain Maker Panel The Small Rain Maker Back Panel, Rain Maker Cover, Rain Maker Rotator, Spinner Hub, and Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Rain Maker Window shall be made from .118 Polycarbonate sheet. 1644-RND - Gear Panel Round The Gear Panel Components shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Gear Panel Windows shall be made from .118 Polycarbonate sheet plastic. 1690-BELL - Small Bell & Hammer Panel The Small Bell and Hammer Panel & Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Small Bell shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1690-CHM - Small Chime Panel The Chime Panels & Chime Hammer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Chime Panel Hubs & Spacers shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Chimes shall be fabricated using 0.75" Galvanized EMT 18ga and will have a multi-stage baked-on powder coat finish. The Chime Panel Bracket shall be punched and formed using 3/16" sheet steel and will have a multi-stage baked-on powder coat finish. 1634 - Labyrinth Panel The Pin Ball Panel Mounting Ring, Labyrinth Panel Rotator, & Labyrinth Panel Front & Back Retainer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Labyrinth Window shall be made from .118 thick polycarbonate sheet plastic. R5 13011 - Half Square Deck Steel Wall R5 The Half Square Deck Steel Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing and 1.029" O.D. 14 gauge steel tubing with a welded 1/4" thick steel tab and shall have a powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 11011 - Half Square Deck R5 Assembly The Half Square Deck shall be fabricated from punched, formed, and welded 12 gauge sheet steel. The Half Square Deck shall be Play Tuffâ„¢ coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and shall have a powder coat finish. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1535 - Crawl-Netix Climber R5 The Crawl-Netix Flange Stiffeners shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Crawl-Netix Net Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Crawl-Netix Net shall be made from 16mm steel-reinforced rope with high-strength co-polymer plastic intersection connectors and machined aluminum and clevises. The Crawl-Netix Rail shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Tube Elbow shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tube Support Plate shall be cut from 1/4" thick sheet steel and will be Powder Coated as specified. The Roto Panel Leg shall be fabricated using 1.660" O.D 11 gauge steel tubing with welded 3/16" thick bracket, and a 1/4" thick steel plate and will be Powder Coated as specified. The Roto Round Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC-2477 - Spin Max Go-Round The Spin Max Base & Top shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Spin Max Bearing House shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Post Support shall be fabricated using 5" O.D. 7 gauge steel post with welded 3/8" thick steel plate and will be Powder Coated as specified. The Spin Max Support Flange shall be formed using 1/4" thick sheet steel and will be Powder Coated as specified. The Spin Max Support Ring shall be fabricated using 2" square 11 gauge steel outer ring with welded 3/8" thick steel splice bars and will be Powder Coated as specified. The Spin Max Go-Round Post shall be fabricated using 5" O.D. 7 gauge steel tubing with welded 3/8" thick steel plates and machined steel spindle and will be Powder Coated as specified. The Speed Limiter Arm shall be fabricated using 1-1/4" square 16 gauge steel tubing with welded 3/8" thick steel plug and 3/16" thick steel clevis and will be Powder Coated as specified. The Speed Limiter Base shall be fabricated using 1/4" thick steel plate with welded 3/16" thick steel tabs, 3/8" thick steel ring blocks and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spin Max Sit Down Rope shall be made from 16mm steel-reinforced rope with machined aluminum end ferrules. The Spin Max Base Spacers & Roto Ferrule Plugs shall be machined from high strength aluminum. The Spin Max Top, Cover Panel & Rope Bridge Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rope Bridge Spacer shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. PC 2436 - Wiggle Beam The Wiggle Beam shall be fabricated using punched, formed and welded 12 gauge sheet steel with reinforcing cross members and gussets and will be Play-Tuff(TM) coated after fabrication. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Spring Mount Puck shall be precision die-cast from high-strength aluminum alloy and will be Powder Coated as specified. The Spring Mount Plate shall be fabricated using 1/4" thick plate steel and will be Powder Coated as specified. The Spring Inground Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Fixed Mount Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/2" thick steel mounting plate and will be Powder Coated as specified. PC-1920 - Spring See-Saw The Post Base shall be fabricated using 5.0" O.D. 7 ga T.S., 1/2" thick sheet steel, and 1/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Spring See Saw Beam shall be fabricated using 4" X 4" x .120" square tube, 1.900" O.D. 11 gauge steel tube with welded 1/4" thick steel mounting plate, brackets, gussets, 12ga steel cap and 10 gauge steel brackets and will have a multi-stage baked-on powder coat finish. The Pivot Axle shall be fabricated from 11 gauge steel tube and will have a multi-stage baked-on powder coat finish. The See Saw Body Components shall be made from high density 3/4" and 1" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will have a multi-stage baked-on powder coat finish. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will have a multi-stage baked-on powder coat finish. The See Saw Bracket shall be fabricated from 10 gauge steel and will have a multi-stage baked-on powder coat finish. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy. The Pipe End Cap shall be fabricated from 1-3/8" OD black acetel copolymer rod. PC 1809 - Triple Hoop The 9' Post R35 shall be fabricated using 3.5" O.D. 11 gauge steel tubing. The Cap & Plugs shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Triple Hoop shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 1510 - Triple Sand and Water Table The Triple Sand & Water Basin shall be formed from clear poly-carbonate. The Triple Sand & Water Table Legs shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel brackets and will be Powder Coated as specified. The Triple Sand & Water Tables, Lids, Turner Collars, Turners, Drain Plug retainer & Drain Plug Grip shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Drain Plug Top & Drain Plug Bottom shall be machined from nylon 6/10. The Drain Plug Tether shall be made from clear vinyl coated 1/4" Dia. steel cable, with crimped aluminum ring terminals. 18016 - Steel Gable Shade Roof The Steel Gable Shade Roof shall be 14 gauge sheet steel welded to 1.315" O.D. 12 gauge steel frame and will be Powder Coated as specified. 18013 - Steel Tri-Shade Roof The Steel Tri-Shade Roof shall be 14 gauge sheet steel welded to 1.315" O.D. 12 gauge steel frame and will be Powder Coated as specified. 4250 - Rectangular Picnic Table The Table Top & Bench shall be fabricated from punched, formed, and welded 14 gauge sheet steel and shall be Play Tuff(TM) coated after fabrication. The Table Frame Brace shall be fabricated from punched and formed 10 gauge sheet steel and shall have a powder coat finish. The Table Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounts and shall have a powder coat finish. The Frame Support shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. 1975 - AccessGlide Assembly The Retainer Plate shall be precision cut from 1/4" thick steel and will be Powder Coated as specified. The Spring Rider Bracket shall be precision cut and formed from 3/16" thick steel and will be Powder Coated as specified. The Trans-Glide Base shall be precision cut and welded from 1/4" thick steel with welded 1.900" 11 gauge steel stiffeners and will be Powder Coated as specified. The Trans-Glide Bench Back & Seat shall be punched, formed and welded from 14 gauge sheet steel with 12 gauge steel gussets and end caps and shall be Play-Tuff(TM) coated after fabrication. The Trans-Glide Bench rail shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handle and 1/4" thick steel mounting tabs and will be Powder Coated as specified. The Trans-Glide Bench Skirt shall be punched, formed and welded from 10 gauge sheet steel and will be Powder Coated as specified. The Trans-Glide Bumper shall be 3/8" thick, 3-ply rubber belt. The Trans-Glide Dampener & Torsion Bracket shall be precision cut and formed from 3/8" thick steel and will be Powder Coated as specified. The Trans-Glide Deck & Transition Deck shall be punched formed and welded from 12 gauge sheet steel and shall be Play-Tuff™ coated after fabrication. The Trans-Glide Dampener Plate shall be made from Ultra High Molecular Weight Polyethylene for lasting durability. The Trans-Glide Drive Arm & Drive Plate shall be precision cut from 1/2" thick steel and will be Powder Coated as specified. The Trans-Glide Driveshaft shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded machined steel spindles and 1/4" thick steel mounting plate and will be Powder Coated as specified. The Trans-Glide Driveshaft Bracket shall be fabricated using welded precision cut 1/2" thick steel tabs and will be Powder Coated as specified. The Trans-Glide Handle shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Drive House shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 10 gauge steel gussets and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Trans-Glide Panel Set shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Trans-Glide Torsion Arm shall be fabricated using 3-1/2" square 3/16" thick wall tubing with welded 1/4" thick steel gussets and 1-1/4" square 1/8" thick wall tubing arm and will be Powder Coated as specified. The Trans-Glide Track Wheel shall be machined Nylon 6/6. The Trans-Glide Wheel Hub shall be fabricated using precision cut and formed 3/8" thick steel and machined stainless steel axles. The Trans-Glide Wheel Hub Stiffener shall be punched, formed, and welded from 10 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.