1706-S - Sectional Spiral Slide Assembly The Spiral Slide Deck shall be precision cut, formed, and welded using 12 gauge thick steel and shall be Play-Tuff(TM) coated after fabrication. The Twister Slide Sections & Hood shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Slide Spacer & Infinity Wall Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Single Slide Leg shall be fabricated using 1.660" 11 gauge steel tubing with 10 gauge HR steel and 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing and 1.029" 14 gauge steel tubing with 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Infinity Wall Sectional Spiral Slide Wall shall be fabricated using 1.315" 12 gauge steel tubing, 12ga HR sheet steel and 1/4" HR steel clevis and will have a multi-stage baked-on powder coat finish. The Twister Sit Down Side Guard Canada shall be fabricated using 1.029" 14 gauge steel tubing with 10 gauge HR steel and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support shall be fabricated using 1.660" 11 gauge steel tubing with 3/16" HR steel 5/8" round bar and will have a multi-stage baked-on powder coat finish. The Sectional Slide Support Bracket shall be fabricated using 3/16" HR steel and will have a multi-stage baked-on powder coat finish. The Roto Panel Deck Mounting Plate shall be fabricated using 1/4" HR steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 18025 CAP - Baseball Cap Roof The Baseball Cap Bill shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 12 gauge sheet steel flanges and will be Powder Coated as specified. The Baseball Cap Bill Panel/Roof Sections shall be punched and formed from .080" thick sheet aluminum and will Powder Coated as specified. The Hex Umbrella Roof Corner Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Hex Umbrella Roof Rafter shall be fabricated from 1" x 2" x .125" wall aluminum tubing and will be Powder Coated as specified. The Hex Umbrella Roof Top Plate shall be fabricated from 10 gauge sheet steel and will be Powder Coated as specified. The Neutron Spinner Cap Dome shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 12801 - Sunrise Climber R5 The Sunrise Climber R5 shall be fabricated using 1.315" O.D. 12 gauge steel rungs with welded 1.900" O.D. 11 gauge steel frame, 1/4" thick steel mounting plate and clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1314 - Access Wall The Access Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel rungs welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1230 - Clover Climber The Clover Climber shall be constructed of 1.900" O.D. 11 gauge tube steel with welded 1.315" O.D. 12 gauge tube steel handles, rungs, and 3/16" thick steel mounting plate. The Clover Climber will be Powder Coated as specified. R5 1214 - Climbing Wall The Chain Mount Bracket shall be laser-cut 1/4" thick steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Climb Chain Hanger shall be laser-cut 3/8" thick plate steel. The Climb Chain Hanger shall have clear zinc plating. The Grip Climb Wall shall be fabricated using punched, formed and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Grip Climb Wall Chain shall be 5/0 galvanized low-carbon steel chain with silver shield finish and shall be Play-Tuff(TM) coated. The Grip Climb Wall Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and 1.315" O.D. 12 gauge steel cross member with welded 3/8" thick steel tab and will be Powder Coated as specified. The Grip Ramp Bracket shall be two part laser-cut and welded 1/4" steel and will be Powder Coated as specified. The Grip Ramp Foot shall be laser-cut from 1/4" steel and will be Powder Coated as specified. The Ramp Grips shall be precision die-cast from a high strength aluminum alloy and shall have a thermoplastic coating. R5 1100 - Deck Identification NO SPECIFICATIONS 1962 - Play Seat The Play Seat shall be punched and formed from 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1313 - Curved Post Handle The Curved Post Handle shall be 1.315" O.D. 12 gauge steel tubing and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1106 - Half Hex Deck 4 Post Assembly The Half Hex Deck 4 Post shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified.