R5-1719-1720 - Roller Slide The Slide Spacer shall be fabricated using formed and welded 12 gauge sheet steel and will be Play-Tuffᵀᴹ coated after fabrication. The Slide Roller shall be made from high viscosity polycarbonate. The Roller Slide Axle shall be cut from 5/8" stainless steel rod. The Roller Slide Bed Brace shall be fabricated from 1.660" O.D. 11 gauge steel tubing with welded 3/4" thick sheet steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Frame shall be fabricated from 1-1/2" x 3" 11 gauge rectangular tubing with riveted 14 gauge sheet steel and 3/16" thick plate steel and will have a multi-stage baked-on powder coat finish. The Roller Slide Leg Tube shall be fabricated from 1.660" O.D. 11 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Roller Slide Blocks shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1707 8 SP - Spiral Tube Slide 96" H The Tube Sections and R5 Tube Slide Panel shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Tube Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded to a 3/16" steel plate with a 5/8" rod at the base as a footing Anchor. The Tube Slide Leg will be Powder Coated as specified. The Inclined Tube Support shall be fabricated from a 1/4" steel pipe plug welded to a 1.660" O.D. 11 gauge 90° Support Elbow inserted and welded into a 1.900" O.D. 11 gauge tube steel Support Leg. The Inclined Tube Support will be Powder Coated as specified. R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1303 TW - Twister Entry Panel w/ Sit Down Hood The Sit Down Hood Support shall be fabricated using 1.315 O.D. 12 gauge steel tubing with welded 1.029 O.D. 14 gauge steel tubing and a 10 gauge steel tab and will be Powder Coated as specified. The Slide Hood R5 shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Twister Entry Panel for Slide hood shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1213 - Firepole Assembly The Firepole shall be fabricated of 1.660" O.D. 11 gauge steel tubing with a .375" steel tab welded onto the end and will be Powder Coated as specified. The Firepole Tab Blocker shall be fabricated from 12 gauge sheet steel and will be Powder Coated as specified. R5-1208 - Ramp R5 The Ramp R5 shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuffâ„¢ coated after fabrication. The Rail Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs and will have a multi-stage baked-on powder coat finish. The Wall Set R5 shall consist of a 1.660" O.D. 11 gauge top rail welded to 1/4" steel mounting clevises with 1.315" O.D. 12 gauge bottom rails, vertical rails and handrails. Handrails shall be attached to vertical rails with 1.029" O.D. 14 gauge handrail standoffs. Vertical rungs shall be evenly spaced 1.029" O.D. 14 gauge steel tubing and will have a multi-stage baked-on powder coat finish. The Sensory Wall Set shall consist of 1.315" O.D. 11 gauge and 1.029" O.D. 14 gauge rails welded to 1/4" steel mounting clevises and tabs and will have a multi-stage baked-on powder coat finish. The Ramp Leg shall consist of 2.375" O.D. 11 gauge steel tubing welded to a 10 gauge steel mounting bracket and a 5/8" round steel footing anchor and will have a multi-stage baked-on powder coat finish. The Sensory Platform Insert shall be precision cut from 12 gauge sheet steel and will have a multi-stage baked-on powder coat finish. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1109 - Balcony Deck R5 The Balcony Deck shall be punched, formed and welded 12 gauge sheet steel. Balcony Deck shall be Play-Tuff(TM) coated after fabrication. The Balcony Deck Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4286 - Bench w/ Back The Bench Divider shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel mounting brackets and will be Powder Coated as specified. The Bench Top shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Bench Frame In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 10 gauge steel mounting plate and will be Powder Coated as specified. The Bench Frame Surface Mount shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.5" x 3" rectangular tube steel and welded 10 gauge steel mounting plates and will be Powder Coated as specified. PC 2478 - Spin Max Pod The Spin Max Pod Cap shall be formed from clear 3/16" poly-carbonate. The Spin Max Bearing House shall be fabricated from a machined 5" O.D. steel tubing with a 1/2" wall welded to a 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Leg shall be fabricated from a 5" O.D. 7 gauge steel post with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Spin Max Pod Half shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". PC 2123 - R3.5 Arch Swing Assembly The Swing Arch & Swing Beam shall be fabricated using 3.5" O.D. 11 gauge galvanized steel tubing and will be Powder Coated as specified. The Arch Swing Casting and Arch Swing Washer shall be cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Swing Chain shall be 7 mm (1/4") PC Grade 30 chain with a silver shield cold galvanized finish. The Swing Seats shall be molded from a UV-stabilized flexible rubber compound with slash-proof, reinforced metal inserts. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1937 - Crunch Handle The Crunch Handle R5 shall be fabricated using 1.315 O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and will be powder coated as specified. The Crunch Handle R35 shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Crunch Handle RV shall be fabricated using 1.315" O.D. 12 gauge steel tubing with a welded 0.625" H.R. round bar crossbar and 1/4" thick stainless steel mounting bracket and will be powder coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be powder coated as specified." 1803 STL - Steel Hex Roof The Steel Hex Roof Corner Bracket shall be formed from 10 gauge sheet steel and will be Powder Coated as specified. The Steel Hex Roof Section and Cap shall be formed from 14 gauge sheet steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1628 - Accessible Driver Panel Assembly The ADA Driver Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Driver Wheel Casting shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. The Mounting Insert shall be precision die-cast from a high strength aluminum alloy. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1410 - Loop Traverse The Loop Traverse 90 Deg. Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab and will be Powder Coated as specified. The Loop Traverse 144" R5 shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports, 1/2" thick steel tab, and 1/4" thick steel clevises and will be Powder Coated as specified. The Loop Traverse shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1-1/2" x 3" 11 gauge steel supports with 1/4" thick steel clevises and will be Powder Coated as specified. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1316 - Twister Entry Panel The Twister Entry Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-Stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1282 - Curved Rung Ladder The Curved Rung Ladder shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plates and 1.315" O.D. 12 gauge steel rungs and will be Powder Coated as specified. 1236 3 - Erector Rock Curve The Erector Rock Curved shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1228 - Bedrock Climber The Bedrock Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Extension shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average double wall thickness of .250". The Bedrock Climber Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. The Bedrock Extension Support shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 10 gauge steel plate and will be Powder Coated as specified. 1209 - Transfer Station The Steps & Decks shall be fabricated from 12 gauge punched sheet steel with reinforcing cross members and gussets. Each Step and Deck shall be Play-Tuff(TM) coated after fabrication. The Step Rails shall be fabricated from 1.315" O.D. 12 gauge and 1.660" O.D. 11 gauge steel tubing and will be powder coated as specified. The Step Deck Legs shall be fabricated from 1.660" O.D. 11 gauge steel tubing welded to a 10 gauge mounting bracket. The Step Deck Leg will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1110 1117 STL - Vertical Deck Filler The Vertical Deck Fillers shall be made from 12 Gauge sheet steel and will be Powder Coated as specified. 1102 - Tri Deck Assembly The Tri Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern and will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy and will be Powder Coated as specified.