RV 21263 - Launch Pad Step RV The Launch Pad Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". RV 12592 - Split Lunar Climber RV The Post Offset Tab Bracket shall be fabricated using precision cut and formed 1/4" thick stainless steel with welded 3/8" thick steel tab and will be Powder Coated as specified. The Split Lunar Climber Post shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/8" thick steel tabs and will be Powder Coated as specified. The Split Lunar Climber Panel, Wings, trim & Event Hanger Caps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. RV 10000 - Revolution Post The Revolution Core Post shall be made from 3.500" O.D. 11 gauge galvanized steel tubing. The Revolution Bottom Cap shall be precision die-cast from a high-strength aluminum alloy. The Revolution Bottom Cap will be Powder Coated as specified. The Revolution Mounting Sleeve shall be precision die-cast from a high-strength aluminum alloy. The Hole Plug shall be precision molded nylon for durability, holding stength and snug installation. RV 1437 - Tri-Pad Jungle Traverse 90 Degree RV The Tri-Pad shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Tri-Pad Jungle Traverse 90° Top Frame RV shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick stainless steel mounting brackets, 3/16" thick stainless steel anchors, and stainless steel pin and shall have a powder coat finish. The Tri-Pad Jungle Traverse Vine shall be made from 16mm steel-reinforced rope with machined aluminum end clevises. The Tri-Pad Jungle Traverse Station shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel plate and 3/16" thick stainless steel anchor and shall have a powder coat finish. The Tri-Pad Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Tri-Pad Support Sleeve shall be fabricated using 2" O.D. 10 gauge stainless steel tubing. RV 1286 - Arched Lunar Climber RV The Arched Wall Climber Panel shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Arched Panel Climber Frame RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing and 1.660" O.D. 11 gauge steel support rails with welded 1/4" thick steel tabs mounting brackets. The Arched Panel Climber Frame RV will be Powder Coated as specified. R35 1309 - R3.5 Half Wall R3.5 HALF WALL: Shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R3.5 PANEL BRACKET: Shall be precision cut from 3/16" HR sheet steel. The R3.5 Panel Bracket shall have a multi-stage baked-on powder coat finish. MOUNTING LUGS: Shall be precision die-cast from a high-strength aluminum alloy. The Mounting Lugs have a multi-stage baked-on powder coat finish. SOCKET CLAMPS: Shall be two-part and precision die-cast from a high strength aluminum alloy. The Socket Clamps have a multi-stage baked-on powder coat finish. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1306 - Double Sit Down Slide Hood The Double Sit Down Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Sit Down Slide Hood Top Rail shall be constructed of 1.315" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Sit Down hood Bar shall be constructed of 1.315" O.D. 12 gauge tube steel and 1.029" O.D. 14 gauge tube steel and will be Powder Coated as specified. R5 1305 - Double Sit Down The Double Sit Down Wall shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a 1.029" O.D. 14 gauge steel extender and will be Powder Coated as specified. R5 1109 GLASS - Glass Balcony Deck The Glass Balcony Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs. All steel decks and walking surfaces shall be punched with a uniform hole pattern and be finished with slip resistant Play-Tuff(TM) coating. The Glass Balcony Deck Wall shall be fabricated of 1.029" O.D. 14 gauge tube steel welded vertically between the top and bottom 1.315" O.D. 12 gauge tube steel rails and will be Powder Coated as specified. The Observation Window shall be made from 1/2" polycarbonate and is to be replaced if damaged or discolored or within 4 years. The Mounting Blocks shall be two part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC-2479 - Mini-Go-Round The Mini-Go-Round Spindle Cap shall be made from precision cut 1/2" thick steel and will be Powder Coated as specified. The Mini-Go-Round Deck & Seat shall be fabricated using punched, formed, and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mini-Go-Round Driver Wheel shall be made from high density 1" thick sheet plastic specially formulated for optimum UV stability and color retention. The Mini-Go-Round Frame shall be fabricated using 1.029" O.D. 14 gauge steel tubing with welded 1/4" thick steel plates and will be Powder Coated as specified. The Mini-Go-Round Center Post shall be fabricated using 3.5" O.D. 11 gauge steel tubing with welded 3/8" thick and 1/4" thick steel mounting plates and will be Powder Coated as specified. The Mini-Go-Round Bracket Spacer shall be made from precision cut 1/4" thick steel and will be Powder Coated as specified. The Mini-Go-Round Bracket shall be fabricated using welded 3/16" and 3/8" thick steel plates and will be Powder Coated as specified. The Mini-Go-Round Top Rail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Merry-Go-Round Bottom Center Post shall be fabricated using 5" O.D. 7 gauge steel tubing with a machined 2.5" O.D. steel spindle and will be Powder Coated as specified. The Spinner Bearing Housing shall be machined using 5" O.D. 1/2" wall with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Post Cap R5 Dome shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. 21011 MNT - Revolution Beam Mid-Support The Revolution Beam Mid-Support shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded stainless steel housing and will be Powder Coated as specified. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 1961 R - Rock Step The Rock Step shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Rock Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1949 - Stand-N-Spin The Spinner Base shall be fabricated from 2.375" O.D. 10 gauge steel tubing welded to 1/4" reinforcer plates and a 3/8" top plate and will be Powder Coated as specified. The Spinner Bearing Housing shall be fabricated using 5" O.D. steel tubing with welded 3/8" thick steel mounting plate and will be Powder Coated as specified. The Stand-N-Spin Post shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" thick steel mounting plate, 3/8" thick steel housing plate and 2.5" O.D. mild steel spindle and will be Powder Coated as specified. The Stand-N-Spin Base & Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Bearing Ball w/ 2 Seals shall be a steel single row, double sealed radial ball bearing with a chrome finish. The External Snap Ring shall be zinc and yellow chromate-plated steel and have an internal diameter of 2". 1810 - Driver Wheel Assembly The Driver Wheel Casting shall be precision die-cast from a high-strength aluminum alloy and will be Powder Coated as specified. The Spindle shall be machined from Ø 1" stainless steel. The Wheel Hub shall be machined from Ø 3-3/4" high strength aluminum alloy and will be Powder Coated as specified. 1702 - Double Slide The Double Slide Spacer shall be fabricated using punched and formed 12 gauge sheet Steel and shall be Play-Tuff(TM) coated after fabrication. The Double Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Double Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" plate steel with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. The Slide Support shall be fabricated of 1.660" O.D. 11 gauge steel tubing welded onto a 3/16" steel plate with a 5/8" steel rod welded to the base as a footing anchor and will be Powder Coated as specified. 1414 1 - Lily Pad Seat-Step Assembly The Lily Pad No Hole shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Step Pad Step Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and will be Powder Coated as specified. 1290 - Boulder Stack Climber The Boulder Stack Bottom Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Boulder Stack Filler Plate shall be fabricated using punched 10 gauge sheet steel and will be Powder Coated as specified. The Boulder Stack Leg shall be fabricated using 1.660" O.D. 11 gauge steel tubing with a welded 1/4" thick steel mounting plate and will be Powder Coated as specified. The Geo Wave Vent Plug shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Rock Spacer shall be made from high density 1" sheet plastic specially formulated for optimum UV stability and color retention. The Top, Mid & Base Rock shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Mounting Lugs shall be precision die-cast from a high-strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1233 - Disc Climber The Disc Climber Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV protection and color retention. The Disc Climber Disc shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Disc Climber Post shall be fabricated using 3.5" O.D. 8 gauge steel tubing with welded 1.315" O.D. 12 gauge steel handles and will be Powder Coated as specified. The Post Cap R3.5 Dome shall be precision die cast from a high-strength aluminum alloy and will be Powder Coated as specified. 1105 - Half Deck Assembly The Half Deck shall be fabricated using punched, formed, and welded 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1101 - Square Deck Assembly The Square Deck shall be constructed using 12 gauge sheet steel which shall be formed and fabricated into required designs and punched with a uniform hole pattern. The Decks will be Play-Tuff(TM) coated after fabrication. The Mounting Blocks shall be two part and precision die- cast from a high strength aluminum alloy. The Mounting Blocks will be Powder Coated as specified.