RV 1934 - Neutron Spinner Mini RV The Neutron Mini Bearing Housing shall be fabricated from a machined 5" O.D. x 1/2" wall tube steel and will be Powder Coated as specified. The Neutron Spinner Mini Handle shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Neutron Spinner Mini Hub Retainer shall be fabricated from 3.5" O.D. 11 gauge galvanized tube steel with welded 3/16" thick steel plate end caps and flange and will be Powder Coated as specified. The Neutron Spinner Mini Post shall be fabricated from 3.5" O.D. 11 gauge galvanized tube steel with welded 3/16" thick steel plates and machined steel spindle. The Neutron Spinner Post Spacer shall be made from high density 1" thick sheet plastic specially formulated for optimum UV stability and color retention. R5 1960 - Tree House Bench R5 The Tree House Bench Base and Top R5 shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1830 STL - Steel Telescope on Wall R5 The Steel Telescope shall be fabricated using 5" O.D. 11 gauge steel tubing with welded 3.5" O.D. 11 gauge steel tubing, and 3/16" thick steel flange, front plate, back plate, and reducer and will be Powder Coated as specified. The Steel Telescope Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs, and 1/4" thick steel tabs and 3/16" thick steel mounting plate and will be Powder Coated as specified. The Steel Telescope Curved Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs, 1/4" thick steel tabs, 3/16" thick steel mounting plate and 3/16" thick steel mounting bracket and will be Powder Coated as specified. The Steel Telescope Wall Mount shall be fabricated using 3/16" thick steel mounting plate with welded 1/4" thick steel mounting tabs and will be Powder Coated as specified. The Steel Telescope Caps shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Steel Telescope Lenses shall be made from .118" thick polycarbonate. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1706 6 - Spiral Slide 6' H The Spiral Slide and Slide Hood shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Spiral Slide Deck shall be fabricated using 12 gauge sheet steel punched and formed with reinforcing cross members and gussets and shall be Play-Tuff(TM) coated after fabrication. The Spiral Slide Wall shall be constructed of 1.315"O.D. 12 gauge tube steel top and bottom rails with welded 1.029" O.D. 14 gauge tube steel vertical rungs with a 1/4" steel wall bracket welded to the outer rails for mounting wall to Spiral Slide and will be Powder Coated as specified. The Spiral Slide Sit Down Bar shall be made from 1.029" O.D. 12 gauge tube steel and will be Powder Coated as specified. The Spiral Slide Wall Brackets shall be fabricated using 1/4" sheet steel Spirals Slide Wall Brackets and 1/4" sheet steel Spiral Slide Wall Tabs and will be Powder Coated as specified. The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Spiral Slide Center Support Post shall be made from 3.5" O.D. 10 gauge tube steel and will be Powder Coated as specified. The Spiral Slide Bottom Collar shall be fabricated from 1/4" sheet steel and will be Powder Coated as specified. R5 1660 - Panel Pal Roto Frame The Panel Pal Roto Frame shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". R5 1615 - Panel Store ROTO The Store Panel Roto shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Counter Set and "Store" Plaque shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1602 - Panel Type 2 (HDPE) The Panel Type 2 HDPE shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Flat Panel Bracket shall be precision laser-cut from 3/16" sheet steel and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5-1601 - Panel Type 1 (Rotomold) The Roto Panel shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Panel Roto Pipe shall be fabricated using Ø1.315 12ga steel tubing. The Roto Panel Bracket shall be fabricated using 10ga sheet steel and will have a multi-stage baked-on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. R5 1317 - Triple Twister Entry Panel The Triple Twister Slide Entry Panel and Stiffener shall be made from high density 3/4" sheet plastic specially formulated for optimum UV-stability and color retention. The Head Rail shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to 1/4" Steel tabs and will be Powder Coated as specified. The Sit Down Side Guard shall be fabricated from 1.029" O.D. 14 gauge tube steel welded to 10 gauge mounting tabs and will be Powder Coated as specified. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1309 - Half Wall (Handle) Assembly The Half Wall R5 shall be constructed of 1.315" O.D. 12 gauge tube steel outer rails with 1.029" O.D. 14 gauge tube steel welded vertically. The Half Wall may also have welded mounting tabs and/or plates and will be Powder Coated as specified. R5 1301 - Wall Steel Bars The Wall Steel Bars shall be fabricated using 1.029" O.D. 14 gauge tube steel welded vertically on 4" centers between vertical 1.315" O.D. 12 gauge tube steel balusters and horizontal 1.315" O.D. 12 gauge tube steel rails, top and bottom and will be Powder Coated as specified. R5 1273 - Stair Climber R5 The ADA Steps 36-26 Wall R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rungs and 1/4" thick steel tabs and will be Powder Coated as specified. The Stair Climber Handle shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded stainless steel pins and will be Powder Coated as specified. The Stair Climber Handrail 36" R5 shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge rungs and 1/4" thick steel tabs and will be Powder Coated as specified. The Stair Climber Steps 36-26 shall be fabricated using punched, formed and welded 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Wall Grips shall be precision die-cast from a high strength aluminum alloy and will have a thermoplastic coating. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1234 - Spiral Step Climber R5 The Spiral Step Climber shall be fabricated from 1.900" O.D. 11 gauge steel tubing with welded 1.315" O.D. 12 gauge steel tubing handles, tread supports, and 1/4" thick steel plates and will be Powder Coated as specified. The Spiral Step Climber Tread shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. R5 1211 - Vertical Step Filler The Vertical Step Filler shall be punched and formed from 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Mounting Lugs shall be precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. R5 1100 - Deck Identification NO SPECIFICATIONS PC 4331 - Urban Elite Bench The Elite Bench Back & Seat shall be fabricated using punched, formed and welded 14 gauge and 12 gauge sheet steel and will be Play-Tuff(TM) coated after fabrication. The Bench Inground Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and will be Powder Coated as specified. The Bench Surface Mount Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel tabs and 3/16" thick steel mounting plates and will be Powder Coated as specified. PC 4221 - Pedestal Picnic Table The Pedestal Seat Frame Mount shall be fabricated using 1.5" x 3" x 0.120" steel tubing with welded 2.375" O.D. 11 gauge steel Mounting Rail, 12 gauge sheet steel End Cap, 1/4" thick steel Mounting Plate, and 10 gauge sheet steel Support Brackets and will be Powder Coated as specified. The Pedestal Table shall be fabricated using punched, formed and welded 14 gauge sheet steel. The Pedestal Table shall be Play-Tuff(TM) coated after fabrication. The Pedestal hardware Pin shall be machined from stainless steel round bar. The Picnic Table Pedestal shall be fabricated using 4" x 0.25" square steel tubing with welded 2.375" O.D.11 gauge steel supports,10 gauge sheet steel Support Brackets, and 12 gauge steel End Cap and will be Powder Coated as specified. The Table Seat shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The 3/8" x 2" S Plate shall be precision laser cut from 1/4" HR sheet steel and will be Powder Coated as specified. PC 4220 S - Square Picnic Table The Bench and Table Top shall be 14 gauge sheet steel punched and formed into the desired shape. The Bench and Table Top shall be Play-Tuff(TM) coated after fabrication. The Square Table Frame Leg shall be 1.660" O.D. 11 gauge tube steel bent into shape with welded 10 gauge end brackets. The Square Table Brace shall be fabricated of 10 gauge sheet steel. The Square Table Brace shall be Play-Tuff(TM) coated after fabrication. The Square Table Frame will be Powder Coated as specified. PC 4218 - Trash Receptacle The Trash Receptacle Body & Lid shall be fabricated using punched and formed 14 gauge sheet steel and shall be Play-Tuffâ„¢ coated after fabrication. The Trash Receptacle Dome Lid shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Trash Receptacle In-Ground Leg shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 3/16" thick steel mounting plate and will have a multi-stage baked-on powder coat finish. The Trash Receptacle Lanyard shall be constructed of vinyl-coated galvanized steel wire and high strength aluminum oval sleeves. PC 2925 - Cactus Climber The Cactus Climber shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Cactus Climber Collar shall be precision cut and formed from 1/4" thick sheet steel and will be Powder Coated as specified. PC 1924 - Quad Teeter Totter The Seesaw Handle Bar Cap, Spacers, Oval End Cap and Trim shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Seesaw Seat shall be fabricated using punched, formed and welded 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Quad Teeter Totter Frame shall be fabricated using 3.5" O.D. 11 gauge steel frame, 2.375" O.D.11 gauge steel stand off, 1.900" O.D. 11 gauge steel posts and 1.315" O.D 12 gauge steel rests with welded 1/4" thick steel base, gussets, tabs and 10 gauge steel brackets and will be Powder Coated as specified. The Quad Teeter Totter Plate shall be precision laser cut from 3/8" thick steel and will be Powder Coated as specified. The Oval End Cap shall be made from high density 3/4" sheet plastic specially formulated for optimum UV stability and color retention. The Playground Event Spring shall be 5-3/4" O.D. with a free height of 14" and will be Powder Coated as specified. The Event Spring Retainer shall be fabricated using precision cut and formed 1/8" thick sheet steel and will be Powder Coated as specified. 18027 18028 - Shade Sail Canopy The Canopy Hub shall be 3.5" O.D. 11 gauge steel post with 1/4" and 3/8" thick steel mounting tabs and will be Powder Coated as specified. The Canopy Tensioner shall be 2" O.D. 11 gauge stainless steel tube, 1/4" thick stainless steel plate, 3/16" steel plugs, and hardware. The Canopy Rafter shall be 2.375" O.D. 10 gauge steel beams and supports, 1/4" and 1/2" steel mounting tabs, and a 3/16" steel plug and will be Powder Coated as specified. The Upper and Lower Sails shall be UV & mildew resistant woven acrylic fabric, folded and stitched for strength and to accommodate steel cable. 1974 - Gyro-Pod Spinner The Gyro-Pod Capsule Leg shall be fabricated using 2.375" O.D. 10 gauge steel tubing with welded 1/4" x 1-1/2" flat steel reinforcement plates and stainless steel ball bearing and will be Powder Coated as specified. The Gyro-Capsule Top Frame shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1.900" O.D. 11 gauge steel supports, 1/4" thick stainless steel mounting brackets and stainless steel ball bearing and will be Powder Coated as finished. The Gyro-Pod Bearing Hub shall be fabricated using 2-1/4" O.D. machined steel hub with welded 1/4" thick steel plate and will be Powder Coated as specified. The Gyro-Pod Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/4" thick steel mounting plates and will be Powder Coated as specified. The Gyro-Pod Tread Plate shall be made from punched 14 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Gyro-Pod Ring Plate shall be made from precision cut 1/4" thick sheet steel and will be Powder Coated as specified. The Gyro-Pod End & Ring shall be constructed of UV-stabilized, rotationally molded, linear, low density polyethylene with an average wall thickness of .250". The Gyro-Pod Ring Spacer shall be machined from high strength aluminum alloy and will be Powder Coated as specified. The Ball Joint Socket Half shall be made from Ultra High Molecular Weight Polyethylene for lasting durability and minimal rotational resistance. The Split Collar Half shall be made from precision cut and formed 1/4" thick stainless steel and will be Powder Coated as specified. 1710 - Twister Slide The Twister Slide shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Single Slide Leg shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 10 gauge steel plate and will be Powder Coated as specified. The Twister Slide Support shall be fabricated of 1.660" O.D. 11 gauge tube steel welded onto a 3/16" steel plate and will be Powder Coated as specified. 1618 - Seek Plaque Assembly The Seek Panel Plaque shall be made from high-density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. 1413 - Track Ride The Track Ride Beam shall be hot-extruded from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Track Ride Mid Support shall be fabricated using 1.900" O.D. 11 gauge steel tubing with welded 1/2" thick steel mounting tab and will have a multi-stage baked-on powder coat finish. The Track Ride Support shall be fabricated using 2" x 3" x .120" Rec T.S. with welded 1/4" thick steel clevises and will have a multi-stage baked-on powder coat finish. The Track Ride Mount RV shall be fabricated using 2.375" O.D. 11 gauge steel tubing with welded 1/4" thick steel mounting plate and stainless steel housing and will have a multi-stage baked-on powder coat finish. The Track Ride Center Support Bracket shall be fabricated using 1/4" thick sheet steel with welded 1/2" thick steel mounting tab and will have a multi-stage baked-on powder coat finish. The Mounting Blocks, Track Ride End Casting, Brake Casting, & Skate Casting shall be precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. The Track Ride Handle shall be fabricated using 1.029" O.D.14 gauge galvanized steel tubing and 1" O.D. AISI bar stock and will be dipped in thermoplastic coating. The Track Ride Bumper shall be injection-molded from commercial grade rubber. The Track Ride Spacers shall be made from high density 3/4" thick hot extruded polyethylene sheet plastic specially formulated for optimum UV stability and color retention. The Track Ride Skate Wheel shall be machined from high-density urethane. The Track Ride Guide Wheel shall be machined from nylon. 1400 - End Access Ladder The End Access Ladder shall be fabricated using 1.315" OD, 12 gauge steel tubing and will be Powder Coated as specified. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will be Powder Coated as specified. 1310 - Transition Wall The Transition Wall shall be fabricated from 1.315" O.D. 12 guage steel tubing, welded 1.029" O.D. 14 guage vertical rails and handles and 1/2" thick steel tabs and will have a multi-stage baked on powder coat finish. The Socket Clamps shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked on powder coat finish. 1289 - Cliffhanger Climber The Cliffhanger Climber shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1/2" thick steel tabs and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Handrail shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel handle and 3/8" thick steel tabs and will have a multi-stage baked-on powder coat finish. The Cliffhanger Climber Wall shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.029" O.D. 14 gauge steel rails, 1/4" thick steel mounting clevises, 1/4" thick steel tabs, and 1/2" thick steel tab and will have a multi-stage baked-on powder coat finish. The Promenade Deck shall be fabricated using punched, formed, and welded 12 gauge sheet. The Promenade Deck shall be Play-Tuff(TM) coated after fabrication. The Socket Clamps & Mounting Blocks shall be two-part and precision die-cast from a high strength aluminum alloy and will have a multi-stage baked-on powder coat finish. 1236 AL - Access Ladder The Erector Rock Access Ladder shall be fabricated from 1.315" O.D. 12 gauge tube steel welded to a .25" sheet steel Erector Rock Climber Plate and will be Powder Coated as specified. 1236 3 - Erector Rock Curve The Erector Rock Curved shall be manufactured from UV-stabilized LLDPE (linear low-density polyethylene) with an average wall thickness of 1/4". The Grips are precision die-cast from a high strength aluminum alloy and have a thermal-set plastic coating. The Erector Rock Posts shall be 3.5" O.D. 11 gauge galvanized tube steel and will be Powder Coated as specified. 1224 - Stacked Loop Climber The Stacked Loop Climber shall have main rails constructed of 1.660" O.D. 11 gauge tube steel with 1.315" O.D. 12 gauge tube steel stepping/gripping loops welded to the main rails and will be Powder Coated as specified. 1210 - Vertical Ladder The Vertical Ladder shall be fabricated using 1.315" O.D. 12 gauge steel tubing with welded 1.315" O.D. 12 gauge steel rungs and 1/4" thick steel mounting plate and will be Powder Coated as specified. 1206 - ADA Steps with Walls The ADA Steps shall be fabricated using 12 gauge punched steel with reinforcing cross members and gussets. All surfaces to be Play-Tuff(TM) coated. The ADA Step Walls shall be fabricated using 1.315" O.D. 12 gauge steel railing welded to 1.029" O.D. 14 gauge evenly spaced vertical rungs with welded 1/4" brackets and will be Powder Coated as specified. 1202 - Step Deck Assembly The Step Deck 2 shall be fabricated using punched and formed 12 gauge sheet steel and shall be Play-Tuff(TM) coated after fabrication. The Step-Deck Legs shall be fabricated from 1.660" O.D. 11 gauge tube steel welded to a 10 gauge mounting bracket and will be Powder Coated as specified.